manualshive.com logo in svg

Sharp AR-BC260, Operation Manual, Page: 27 / 184

Share
Download
Sharp AR-BC260 Operation Manual Download Page 27

LOADING PAPER

2-5

2

NOTES

●

Be sure to load 5-1/2" x 8-1/2" paper, A6 paper, A5
paper, and postcards as shown in the diagram
below.

A6 paper, post cards.
5-1/2" x 8-1/2" paper, A5 paper.

●

When loading plain paper other than paper
recommended for color, SHARP standard paper,
special media other than postcards, SHARP-
recommended transparency film, or paper to be
printed on the back, the paper must be loaded one
sheet at a time. Loading more than one sheet at a
time will cause misfeeds.

●

Before loading heavy paper, straighten any curling
in the paper.

●

When adding paper, remove any paper remaining
in the tray, combine it with the paper to be added,
and reload as a single stack.

●

Do not use paper that has already been printed on
by a plain paper fax machine or a laser printer.
This may cause printed images to become dirty.

●

When printing on transparency film, be sure to
remove each sheet as it exits the machine.
Allowing sheets to stack in the output tray may
cause curling.

●

Use only SHARP-recommended transparency
film. Insert the film so that the rounded corner is on
the left for horizontal loading, or on the right for
vertical loading.

●

When loading multiple sheets of transparency film
in the bypass tray, fan the sheets several times
before loading.

Horizontal
loading

Vertical
loading

ApollonII_general-copy_SEC.book  5 

ページ

  

２００４年９月６日　月曜日　午後４時５７分

Summary of Contents for AR-BC260

























































































































































































Reviews:

No comments