manualshive.com logo in svg

Sharp AR-BC260, Operation Manual, Page: 134 / 184

Share
Download
Sharp AR-BC260 Operation Manual Download Page 134

SPECIFICATIONS

8-4

Reversing single pass feeder

Duplex bypass/inverter unit (optional)

Original sizes

5-1/2" x 8-1/2" to 11" x 17" (A5 to A3)

Original weight

15 to 24 lbs. (56 to 90 

g

/m

2

)

Capacity

Up to 40 sheets (8-1/2" x 11", 21 lbs. (A4,  80 

g

/m

2

))

Up to 30 sheets (8-1/2" x 14" or larger, 21 lbs. (B4 or larger,  80 

g

/m

2

))

Power supply

Supplied from machine

Dimensions

22-61/64" (W) x 17-9/64" (D) x 5-1/4" (H)
(583 mm (W) x 435 mm (D) x 133 mm (H))

Weight

Approx. 11.9 lbs. (Approx. 5.4 k

g

)

Number of sheets

1 sheet (non-stack method)

Paper size

Face-up output: Same as paper feed specifications of machine
Face-down output: 12"x18", 11"x17", 8-1/2"x14", 8-1/2"x13", 8-1/2"x11", 8-1/2"x11"R,

7-1/4"x10-1/2"R, 8-1/2"x5-1/2", A3W, A3, B4, A4,  A4R, B5, B5R,
A5

Page weight

Face-up output: 17 to 80 lbs. (64 to 300 

g

/m

2

)

Face-down output: 17 to 54 lbs. (64 to 200 

g

/m

2

)

Transport reference point

Center reference point

Dimensions

6-5/32" (W) x 17-29/64" (D) x 17-1/64" (H)
(156 mm (W) x 443 mm (D) x 432 mm (H))

Weight

Approx. 14.3 lbs. (Approx. 6.5 k

g

)

As a part of our policy of continuous improvement, SHARP reserves the right to make design and specification
changes for product improvement without prior notice. The performance specification figures indicated are
nominal values of production units. There may be some deviations from these values in individual units.

ApollonII_general-copy_SEC.book  4 

ページ

  

２００４年９月６日　月曜日　午後４時５７分

Summary of Contents for AR-BC260

























































































































































































Reviews:

No comments