Sharp AR-BC260, Operation Manual, Page: 181 / 184

15
PROGRAMS FOR COPY MODE
Exposure adjustment
Use this program to lighten or darken copies in the
automatic exposure mode. The factory setting is "5".
"1" indicates lighter density and "9" indicates darker
density on the touch panel.
Rotation copy setting
If this program is set, the image of originals will rotate
when the orientation of the originals does not match
that of the copy paper.
(Rotation copy will function only if the auto paper select
or auto image mode has been selected.)
Add or change extra preset ratios
When using inch sizes, there are normally four preset
enlargement ratios and four preset reduction ratios.
When using AB sizes, there are normally five preset
enlargement ratios and five preset reduction ratios.
This program allows you to add two more preset
enlargement ratios and two more preset reduction
ratios. This program also allows you to change a preset
ratio.
Initial margin shift setting
Set the initial margin shift value with this program.
The value can be set from 0" to 1" in 1/8" increments or
from 0 mm to 20 mm in 1 mm increments.
If an optional duplex module/2 x 500 sheet paper
drawer (AR-D19N) and duplex bypass/inverter unit
(AR-RB1) are not installed, the value for the reverse
side (side 2) is not displayed.
Erase width adjustment
Set the initial setting of the amount of the erase area
with this program.
The values can be set from 0" to 1" in 1/8" increments
or from 0 mm to 20 mm in 1 mm increments.
Setting a maximum number of copies
Use this program to limit the maximum number of
copies per copy run which can be input in the copy
quantity display.
A number from 1 to 999 can be set.
Initial color balance setting
Color balance settings that have been adjusted using
the special "Color Balance" function explained on page
6-14 of the "Operation manual (for general information
and copier operation)" can be called up and set as
initial color balance settings* by storing them ahead of
time in a job program (page 6-25 of the "Operation
manual (for general information and copier
operation)"). Use this feature when you want to
repeatedly use settings for a favorite color or for
correction when a change occurs in the color balance.
* Preset values displayed when you select the special
"Color Balance" function. The factory default settings
are the "0" position for all eight levels of each color.
When the [INITIAL COLOR BALANCE SETTING] key
is touched, the following display will appear.
If a job program number key is touched that does not
have color balance settings, a warning message will
appear.
To return color balance settings that have been stored
as initial settings to the factory default settings (the "0"
position for all eight levels of each color), touch the
[RETURN TO THE FACTORY DEFAULT SETTINGS.]
key.
Auto color calibration
The Auto Color Calibration program enables automatic
color gradation correction when the color reproduction
is incorrect.
When the [AUTO COLOR CALIBRATION] key is
touched, the following display will appear.
NOTE
For copying from 5-1/2" x 8-1/2" or A5 size originals
onto 5-1/2" x 8-1/2"R or A5R paper, this program
must be set.
NOTE
Only an added preset ratio can be changed.
NOTE
The color gradation may not be sufficiently
corrected after one correction cycle. If so, execute
the program again.
KEY OPERATOR PROGRAMS
OK INITIAL COLOR BALANCE SETTING
PRESS PROGRAM NUMBER IN WHICH COLOR BALANCE PROGRAM IS REGISTERED.
1
6
2
7
3
8
4
9
5
10
RETURN TO THE FACTORY DEFAULT
SETTINGS.
KEY OPERATOR PROGRAMS
OK AUTO COLOR CALIBRATION
USE 11"X17" OR A3 PAPER FOR THIS ADJUSTMENT.
PRESS [EXECUTE] TO PRINT THE TEST PATCH.
EXECUTE
ApollonII_keyope_sec.fm 15 ページ ２００４年９月２日 木曜日 午後２時５０分