Sharp AR-BC260 Operation Manual Download Page 60

Page: 60 / 184

SADDLE STITCH FINISHER

3-12

Troubleshooting saddle stitch finisher problems

Check the list below before calling for service.

* When a hole punch module is installed

Problem

Check

Solution or cause

Stapling position is
not correct
(including saddle
stitch).

Stapling position not set properly?

Check the stapling position setting. (See
pages 3-4, 3-13 and 3-14.)

The saddle stitch
finisher does not
operate.

Are any saddle stitch finisher covers open?

Close all covers. (See page 3-10 and 3-11.)

Message indicating need to remove paper
from the stapler compiler displayed?

Remove all remaining paper from the stapler
compiler referring to step 4 on page 3-8.

Stapling cannot be
performed (including
saddle stitch).

Message to check the staple unit
displayed?

Remove jammed staples. (See page 3-8.)

Message to add staples displayed?

Replace the staple cartridge. (See page 3-7.)
Check that a staple cartridge has been
installed. (See page 3-7.)

Different size paper included?

Stapling cannot be performed onto different
size paper.

Is the paper badly curled, preventing
stapling?

Differences in paper quality and type may
result in bad curling of output paper. Take the
paper out of the tray or bypass tray, turn it
around, and reload it so that the top and
bottom edges are reversed.

The punch hole
positions are not
correct*

The punch function is not set to the correct
punch positions.

Check the allowed hole punch positions. (See
page 3-5.)

Cannot be punched.*

Message to check the punch module
displayed?

Dispose of punch scraps. (See page 3-9.)

Mixed paper sizes?

Punching is not possible when different paper
sizes are mixed together.

Paper is badly curled and the output paper
is not punched.

ApollonII_general-copy_SEC.book 12

ページ

２００４年９月６日　月曜日　午後４時５７分

Summary of Contents for AR-BC260

























































































































































































Search results

Summary of Contents for AR-BC260

Reviews:

Sharp AR-BC260, Operation Manual, Page: 60 / 184

Search results

Summary of Contents for AR-BC260

Reviews: