Sharp AR-BC260 Operation Manual Download Page 56

Page: 56 / 184

SADDLE STITCH FINISHER

3-8

■

Staple jam removal

Unlatch the saddle stitch finisher and slide
it away from the main unit.

Open the front cover.

Turn roller rotating knob C as shown in the
illustration until the blue indication is
seen.

Remove the paper from the stapler
compiler.

If saddle stitching was selected, open the
saddle stitch section cover.

Remove the misfed paper.

Be careful not to tear the
misfed paper during
removal.

Close the saddle stitch section cover.

Pull out the stapler section.

Turn roller rotating knob A in the direction
of the arrow to move the staple unit to the
front.

Turn the roller rotating
knob until the triangle
mark is aligned with the
index.

Remove the staple box.

Blue

Roller rotating
knob C

Roller rotating
knob A

Staple unit

ApollonII_general-copy_SEC.book 8

ページ

２００４年９月６日　月曜日　午後４時５７分

Summary of Contents for AR-BC260

























































































































































































Search results

Summary of Contents for AR-BC260

Reviews:

Sharp AR-BC260, Operation Manual, Page: 56 / 184

Search results

Summary of Contents for AR-BC260

Reviews: