Schweitzer Engineering Laboratories SEL-221F Instruction Manual Download Page 22 | Manualshive

Page: 22 / 231

background image

Figure 1.1:

System Single Line Diagram for the SEL-221F-1 Relay Modification
Explanation

OTHER SEL-221F RELAY MODEL VARIATIONS

This model variation description is provided for comparison purposes.

SEL-221F-8 Relay

The  SEL-221F-8  relay  has  several  differences  from  the  basic  SEL-221F  relay  model.  A
Level  2  access  attempt  does  not  pulse  the  ALARM  contacts  as  in  the  SEL-221F  relay.
Instead,  the  ALARM  contact  pulses  for  four  seconds  after  three  unsuccessful  Level  1  or  2
access  attempts.  DATE,  TIME,  TRIGGER,  and  IRIG  command  execution  requires  Level  2
access. In contrast, the basic SEL-221F relay requires only Level 1 access for these com-
mands. TARGET command execution from Level 1 only displays targets. TARGET
command  execution  from  Level  2  displays  targets  and  allows  the  operator  to  change  front
panel  LED  assignments.  Excluding  these  differences,  the  SEL-221F-8  relay  is  identical  to  the
SEL-221F  relay.

GENERAL DESCRIPTION

Because the -1 relay variation is derived from the SEL-221F relay, this manual refers to both
variations (standard and -1) as the SEL-221F relay.

The  SEL-221F  Phase  and  Ground  Distance  Relay  with  fault  locator  simultaneously  provides
high-speed  and  time  delayed  protection  for  transmission,  subtransmission,  and  distribution
lines.  A  24-bit  Relay  Word  combines  mho  distance  elements,  overcurrent  elements,  dir-
ectional  element,  timers,  and  data  and  control  bits.  You  can  program  the  tripping,  output,
and  reclosing  logic  through  Relay  Word  bit  combinations  to  control  the  relay  outputs.

Date Code 920508

Introduction

SEL-221F, -1 Instruction Manuel

1-3

«
...
20
21
22
23
24
...
»

Summary of Contents for SEL-221F








































































































































































































































Reviews:

No comments

Related manuals for SEL-221F

Brand: Zander Aachen Pages: 10

Brand: Zennio Pages: 2

Brand: Schrack Pages: 4

Brand: Dossena Pages: 2

Brand: Dossena Pages: 4

Brand: Dossena Pages: 4

Brand: Dossena Pages: 4

Xcomfort CSEZ-01/18

Brand: Moeller Pages: 2

Brand: LEGRAND Pages: 2

Brand: ABB Pages: 152

Brand: LVS Pages: 4

Brand: GE Pages: 600

Brand: 4B Pages: 31

Brand: Zamel Pages: 4

Brand: MICROENER Pages: 25

Brand: MICROENER Pages: 32

Brand: Real-El Pages: 8

Brand: philippi Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands