Getting Started
P746/EN GS/G31
(GS) 3-
34
MiCOM
P746
CT AND VT RATIOS
Restore Defaults
Main VT Primary
Clear Events
Duration
Default Display *
No Operation
110,0 V
No
1.500 ms
Description
Setting Group
Main VT Sec'y
Clear Faults
Trigger Position
Local Values
Select via Menu
110,0 V
No
33,30 %
Primary
Active Settings
Tx CT *
Clear Maint
Trigger Mode
Remote Values
Group 1
No
Single
Primary
Save Changes
Polarity
Alarm Event
Analog Channel 1
*
Measurement Ref
No Operation
Standard
Enabled
VAN
VA
Copy From
Primary
Relay O/P Event
Analog Channel 2
*
Measurement Mode
Group 1
1.000 kA
Enabled
VBN
0
Copy To
Secondary
Opto Input Event
* front panel user
No Operation
1000 A
Enabled
interface only
* x = 1 to 6 (1 box)
Setting Group 1
x = 1 to 18 (3 box)
General Event
Analog Channel 20 *
Enabled
Enabled
IB-T6 / IX-T17
Setting Group 2
Fault Rec Event
Analog Channel 21 *
Disabled
Enabled
IC-T6 / IX-T18
Setting Group 3
Maint Rec Event
Digital input 1
*
Disabled
Enabled
Output R1
Setting Group 4
Protection Event
Input 1 Trigger
*
Disabled
Enabled
No Trigger
OP Mode
Clear Dist Recs
Digital Input 2
*
One Box Mode
No
Output R2
Diff Protection
DDB 31 - 0
Input 2 Trigger
*
Enabled
111111111111111
No Trigger
Dead Zone OC
DDB 63 - 32
Disabled
111111111111111
Overcurrent
DDB 95 - 64
Digital Input 32
*
Enabled
111111111111111
Function key 10
Earth fault
Input 32 Trigger
*
Enabled
Trigger L/H
CB fail
Setting Values
DDB 2015 - 1984
Disabled
Primary
111111111111111
* see section P746/EN T
for the default settings.
Supervision
Control Inputs
DDB 2047 - 2016
Disabled
Visible
111111111111111
Input Labels
Control I/P Config
Visible
Visible
Output Labels
Control I/P Labels
Visible
Visible
CT & VT Ratios
Direct Access
Visible
Enabled
Record Control
Function Key
Visible
Visible
Disturb Recorder
RP1 Read Only
Visible
Disabled
Measure't Setup
RP2 Read Only
Visible
Disabled
Comms Setting
NIC Read Only
Visible
Disabled
MEASURE'T SETUP
(When Visible)
CONFIGURATION
RECORD CONTROL
(When Visible)
DISTURB RECORDER
(When Visible)
GS
Commission Tests
LCD Contrast
Visible
11
Summary of Contents for MiCOM P746
