sauter equitherm EQJW245 Operating Manual Download Page 81

Page: 81 / 127

EQJW245

81/127

www.sauter-controls.com

Communication functions

6.3 Modbus

communication

The EQJW245 can respond to enquiries in the Modbus RTU protocol as a slave.

For this purpose, an RS-485 two-wire bus is connected to terminals 18 and 19.

A suitable Modbus master (BMS centre) can send enquiries or commands via

this bus. Up to 247 devices can be addressed in a communication network based

on the Modbus RTU protocol via an RS485 interface. Up to 32 devices can be

connected within a bus segment.

To enable the function, CP02 must be set to 2 (see Section 3.2.3). A unique

address must be assigned at CP05 and the transmission speed (Baud rate) must

be selected with CP03. The data format supported by the controller is 8n1, i.e. the

data format comprises 8 data bits, no parity bits and one stop bit.

The following commands are supported:

Read Coil:

AA 01 XX XX 00 01 CC CC

-- -- ----- ----- ----- Coils =

Adr RC CoilNr Coils CRC

Anzahl d. zu lesenden Coils

Antwort:

AA 01 01 YY CC CC

-- -- -- -- -----

Anz =

Adr RC Anz Dat CRC

Anzahl der folgenden Datenbytes

___________________________________________________________________

Read Holding:

AA 03 XX XX 00 01 CC CC

-- -- ----- ----- ----- Reg. =

Adr RH HR-Nr Reg. CRC

Anzahl der zu lesenden Register

Antwort:

AA 03 02 XX XX CC CC

-- -- -- ----- -----

Anz =

Adr RH Anz Daten CRC

Anzahl der folgenden Datenbytes

___________________________________________________________________

Set Coil:

AA 05 XX XX YY 00 CC CC

YY = 0xFF zum setzen,

-- -- ----- ----- ----- 0x00 zum löschen
Adr SC CoilNr Data CRC

(Antwort identisch)
___________________________________________________________________

Set Holding:

AA 06 XX XX YY YY CC CC

-- -- ----- ----- -----
Adr SH HR-Nr Data CRC

(Antwort identisch)

___________________________________________________________________

Modbus communication-commandos

Fig.8

Summary of Contents for equitherm EQJW245
































































































































Search results

Summary of Contents for equitherm EQJW245

Reviews:

Related manuals for equitherm EQJW245

Brands by name

Popular brands

sauter equitherm EQJW245, Operating Manual

Search results

Summary of Contents for equitherm EQJW245

Reviews:

Related manuals for equitherm EQJW245

Brands by name

Popular brands