sauter equitherm EQJW245 Operating Manual Download Page 63

Page: 63 / 127

EQJW245

63/127

www.sauter-controls.com

Operation

06:40

Turn the input knob.

The time for the switching command

is changed.

06:40

Press the input knob.

The time for the switching command

is confi rmed.

06:40

Turn the input knob.

Select the mode for the switching

command.

06:40

Press the input knob.

The mode is confi rmed.

Changing and deleting a switching command

4.4.4

Show the switching command as described in the Section on ‚View switching

commands‘, e.g.:

00:00

Press the input knob.

The switching command is called up

Turn the input knob.

Choose whether you want to delete

the switching command (Clr) or
change it (SEt).

Press the input knob.

Your selection is confi rmed.

If the switching command was

deleted, the next switching command
is shown.

0000

For a change, the rest of the

procedure is as described in the
Section on ‚Enter a switching
command‘.

06:40

... etc.

Summary of Contents for equitherm EQJW245
































































































































Search results

Summary of Contents for equitherm EQJW245

Reviews:

Related manuals for equitherm EQJW245

Brands by name

Popular brands

sauter equitherm EQJW245, Operating Manual

Search results

Summary of Contents for equitherm EQJW245

Reviews:

Related manuals for equitherm EQJW245

Brands by name

Popular brands