sauter equitherm EQJW245 Operating Manual Download Page 14

Page: 14 / 127

14/127

www.sauter-controls.com

EQJW245

Description of the operating controls

Middle rotary switch (heating 2)

2.3

EQJW245 - Middle rotary switch (heating 2)

Fig.3

Operating modes

Inputs

Automatic mode according to
swithing programme

Setpoint adjustment normal mode

Regulator is continuously in normal
mode

Setpoint adjustment Reduced mode

Regulator is continuously in Redu-
ced mode

Enter weekly and yearly programme
for heating

Regulator is continuously in back-
up mode

Limited (unlimited) temperature
change

Access to manual mode for heating

Access to log book

Normal mode corresponds to nominal mode as per EN 12098-1

Back-up mode means that the heating is switched off and the anti-frost

function is active.

Bottom rotary switch (domestic water)

2.4

EQJW245 - Bottom rotary switch (domestic water)

Fig.4

Operating modes

Inputs

Automatic mode for domestic
hot water according to switching
programme

Setpoint for increased domestic fot
water temperature

Continuous heating to increased
domestic water temperature

Sollwert normale Trinkwassertemperatur

Continuous heating to normal
domestic water temperature

Eingabe Wochenprogramm Trinkwasser

Trinkwasserladung abgeschaltet

Eingabe Wochenprogramm konfi gurier-
barer Ausgang

Zugang zum Handbetrieb für Trink-
wasser, konfi gurierbarer Ausgang

einmalige Trinkwasserladung

If the rotary switches are used to select a prohibited combination of positions, e.g.

simultaneous entry of setpoints for heating and domestic water preparation, the

controller will show this symbol:

. In this case, one of the switches should be

set to the

symbol or to another mode.

Summary of Contents for equitherm EQJW245
































































































































Search results

Summary of Contents for equitherm EQJW245

Reviews:

Related manuals for equitherm EQJW245

Brands by name

Popular brands

sauter equitherm EQJW245, Operating Manual

Search results

Summary of Contents for equitherm EQJW245

Reviews:

Related manuals for equitherm EQJW245

Brands by name

Popular brands