sauter equitherm EQJW245 Operating Manual Download Page 19

Page: 19 / 127

EQJW245

19/127

www.sauter-controls.com

Commissioning

2008

Turn the input knob.

The year is changed.

01.01

Press the input knob.

The year is confi rmed and the day/

month is shown.

29.04

Turn the input knob.

The date is changed.

29.04

Press the input knob,

The new date is confi rmed.

3.2 Commissioning

level

In commissioning level, a specialist can perform the basic settings on the GZP

which are important for commissioning. Direct access to specifi ed service

parameters is enabled.

Incorrect parameterisation (setting) of the heating controller

It can cause major faults or damage to the installation.

The commissioning level must only be enabled by a specialist.

Some of the parameters cannot be changed. They can only be viewed (version

number, status information).

Access to commissioning level

3.2.1

In order to access commissioning level, the bottom rotary switch must fi rst be

moved to one of the following positions (see chapter 4.1):

Off mode

Continuous heating to normal domestic water temperature

Continuous heating to increased domestic water temperature

Automatic mode

The middle rotary switch must be in one of the following positions (see section

2.1).

NOTICE

Summary of Contents for equitherm EQJW245
































































































































Search results

Summary of Contents for equitherm EQJW245

Reviews:

Related manuals for equitherm EQJW245

Brands by name

Popular brands

sauter equitherm EQJW245, Operating Manual

Search results

Summary of Contents for equitherm EQJW245

Reviews:

Related manuals for equitherm EQJW245

Brands by name

Popular brands