sauter equitherm EQJW245 Operating Manual Download Page 18

Page: 18 / 127

18/127

www.sauter-controls.com

EQJW245

Commissioning

15:06

Press the input knob again.

The new time is confi rmed.

If several devices are connected to each other via a device bus (see 3.4.4) and

you set the clock on one device, the time and date are also set on all the other

devices.

Setting the

3.1.2

date

To enable you to set the date, you must fi rst move the bottom rotary switch into

one of the following positions (see 4.1):

Off mode

Continuous heating to normal domestic water temperature

Continuous heating to increased domestic water temperature

Automatic mode

The middle rotary switch must be in one of the following positions (see section

2.1).

Back-up mode

Reduced mode

Normal mode

Automatic mode

15:06

Set the top rotary switch to automatic

mode.
The time is shown.

0 1.0 1

Turn the input knob until the date is

displayed
(day/month and year are shown

alternately).

2000

Press the input knob.

The number of the year fl ashes...

Procedure

Summary of Contents for equitherm EQJW245
































































































































Search results

Summary of Contents for equitherm EQJW245

Reviews:

Related manuals for equitherm EQJW245

Brands by name

Popular brands

sauter equitherm EQJW245, Operating Manual

Search results

Summary of Contents for equitherm EQJW245

Reviews:

Related manuals for equitherm EQJW245

Brands by name

Popular brands