sauter equitherm EQJW245 Operating Manual Download Page 93

Page: 93 / 127

EQJW245

93/127

www.sauter-controls.com

Using the controller

Using the

controller

General information

8.1

The EQJW245 controller is used for weather-compensated fl ow temperature

control of two heating circuits. An additional room temperature connection is

possible. The controller changes the operating status in accordance with the

switching commands that are entered, on a time-dependent basis. In addition, hot

water preparation can be controlled.

It has an anti-frost function, an automatic summer time changeover, an anti-

jamming feature for the pump and a screed curing function. A communication

interface allows connections with other devices and with a Modbus control station

(also via modem), or automatic transmission of fault messages to a mobile

phone as SMS messages via modem. Two rotary switches allow immediate mode

changes and direct access to the main settings. An input knob makes it easy to

change the device‘s settings.

This application requires an additional safety thermostat.

Before the installation is commissioned, the slope of the characteristic and the

fl ow temperature limit must always be checked.

Depending on the application, the following settings are recommended:

characteristic slope

SERVice-Parameter SP41

Value 1,4 (

)

fl ow temperature limit

SERVice-Parameter SP22

Value 75°C (

)

characteristic slope

SERVice-Parameter SP41

Value 0,6

fl ow temperature limit

SERVice-Parameter SP22

Value 50°C

The recommended values have been tried and tested but they are not necessarily

the ideal solutions for every installation. No liability is accepted for the values

indicated here.

Examples of use

8.2

Some typical and common applications for the control models stored in the

EQJW245 are described below. However, not all of the heating controller‘s

capabilities are described. By parameterising accordingly, further applications can

be included, enabling the equitherm

EQJW245 to be adapted to a wide range of

installations.

NOTICE

Radiator heating

Floor heating

Summary of Contents for equitherm EQJW245
































































































































Search results

Summary of Contents for equitherm EQJW245

Reviews:

Related manuals for equitherm EQJW245

Brands by name

Popular brands

sauter equitherm EQJW245, Operating Manual

Search results

Summary of Contents for equitherm EQJW245

Reviews:

Related manuals for equitherm EQJW245

Brands by name

Popular brands