sauter equitherm EQJW245 Operating Manual Download Page 86

Page: 86 / 127

86/127

www.sauter-controls.com

EQJW245

these level bits are set again after a timeout period of 30 minutes (unless this

timeout function was disabled in CP27). From then on, the controller resumes

control of all functions.

Modem operation

6.4

A modem of type KT DataMod10 can be connected to the communication

interface. This modem can be used for Modbus communication with a control

station, or to send error messages via SMS. In both cases, the controller can

build up a connection automatically if a fault occurs. The two functions can be

combined. In this case, an error is signalled via SMS and via Modbus.

Connection with the modem

6.4.1

A special connection line

(included in the scope of delivery for the modem) is

used to connect with the modem on terminals 18 to 21 of the controller base. For

this purpose, the end of the line is plugged into the controller base terminals with

the pins in such a way that the screws are visible. Then tighten the four screws in

question on the controller base.

Modbus operation via modem

6.4.2

CP02 must be set to 3 or 5. In Modbus mode, the controller accepts calls from a

control station to the modem. In the event of an error, the control station is called

on the telephone number entered at CP06.

In the case of a modem connection, before executing write commands via

Modbus, the valid code number (123) must be written to Modbus register 40145.

Otherwise, only read commands will be processed. This is used to prove the

legitimation of the control system. If an incorrect code number is entered three

times via Modbus, this is recorded as a prohibited access attempt. As a result, an

error bit is set and the control station is dialled by the controller.

Sending SMS if there is a fault on the installation

6.4.3

A modem enables the controller to send an error message to a mobile phone. As

soon as a fault is registered in the device status register of the controller, an SMS

message is sent. This requires modem access from a provider (SMSC = Short

Message Service Center) which accepts SMS messages in TAP protocol. The

message on the display of the mobile phone will then read something like this:

‚Heating controller EQJW245/device status: [XXXX]/Note: 0 = no error. >0 = error

has occurred‘

The value shown for the device status corresponds to the value of SERVice

parameter SP02. The error that has occurred is stored in this value in encoded

form (see Section 7.1.2). The SMS Center usually sends the date, time and

sender‘s telephone number for this message.

The line between the controller and the modem must not be longer than 1.5 m for reasons related to EMC

Summary of Contents for equitherm EQJW245
































































































































Search results

Summary of Contents for equitherm EQJW245

Reviews:

Related manuals for equitherm EQJW245

Brands by name

Popular brands

sauter equitherm EQJW245, Operating Manual

Search results

Summary of Contents for equitherm EQJW245

Reviews:

Related manuals for equitherm EQJW245

Brands by name

Popular brands