sauter equitherm EQJW245 Operating Manual Download Page 65

Page: 65 / 127

EQJW245

65/127

www.sauter-controls.com

Operation

----

Push the input knob.

This selects the calendar programme.

You see ‚_ _ _ _‘ or the fi rst switching

command if one is present.

View switching commands

4.5.2

31.12

Turn the input knob.

The individual switching commands

are shown, if any are present.
An empty switching command is

shown as ‚_ _ _ _‘.

Enter a switching command

4.5.3

----

Turn the input knob until you reach

the next empty switching command.

01.01

Push the input knob.

The new switching command is

shown.

01.05

Turn the input knob.

The date for the switching command

is changed.

01:05

Push the input knob.

The date for the switching command

is confi rmed.

01:05

Turn the input knob.

Select the mode for the switching

command.

01:05

Push the input knob.

The mode is confi rmed.

Changing and deleting a switching command

4.5.4

Show the switching command as described in the Section on ‚View switching

commands‘, e.g.:

01:05

Press the input knob.

The switching command is called up.

Turn the input knob.

Summary of Contents for equitherm EQJW245
































































































































Search results

Summary of Contents for equitherm EQJW245

Reviews:

Related manuals for equitherm EQJW245

Brands by name

Popular brands

sauter equitherm EQJW245, Operating Manual

Search results

Summary of Contents for equitherm EQJW245

Reviews:

Related manuals for equitherm EQJW245

Brands by name

Popular brands