manualshive.com logo in svg

Satel INT-GSM, Manual, Page: 9 / 43

Share
Download
Satel INT-GSM Manual Download Page 9

SATEL INT-GSM 

7 

The address set must be different from that in the other devices connected to the keypad bus 
of the control panel (the control panel does not support devices with the same address). 

4.3  Installation of antenna 

The INT-GSM module is delivered with an antenna. The antenna can be replaced with 
another antenna mounted on the enclosure or at some distance from it. If this is the case, 
you will need the IPX-SMA adapter. 
Using the antenna mounted at some distance from the enclosure is recommended wherever 
thick masonry walls, metal partitions etc. may decrease the range of radio signal at the 
module installation place. 
The antenna must not be installed in parallel to low-voltage electrical wires, or it can affect 
performance of the antenna. 

4.4  Connection 

The module can be connected directly to the alarm control panel or to the ETHM-1 Plus 
module. It is recommended that unshielded non-twisted cable to be used. 

4.4.1  Connecting to the alarm control panel 

 

 

Fig. 4. The way of connecting the module with the alarm control panel. 

 
1.  Connect the +12V, COM, DTM and CKM module terminals to the control panel terminals 

(Fig. 4). To connect the +12V and COM terminals, use flexible conductors with a cross-
section of 0.5-0.75 mm

2

, or rigid conductors with a cross-section of 1-2.5 mm

2

. If you use 

the “twisted pair” type of cable to connect the DTM and CKM terminals, keep in mind that 
the CKM (clock) and DTM (data) signals must not be transmitted using one pair of twisted 
wires. The wires must be run in one cable. 

2.  If the control panel is to be configured via the module using the DLOADX program, 

connect the module RS-232 port to the control panel RS-232 port. Depending on the 
control panel, use the following cable to make the connection: 
INTEGRA with connector socket of RJ / INTEGRA Plus type: 

RJ/PIN5

 (Fig. 5), 

INTEGRA with connector socket of PIN5 type: 

PIN5/PIN5

 (Fig. 6). 

The above mentioned cables are available in SATEL's product offering. 

Summary of Contents for INT-GSM












































Reviews:

No comments