manualshive.com logo in svg

Satel INT-GSM, Manual, Page: 5 / 43

Share
Download
Satel INT-GSM Manual Download Page 5

SATEL INT-GSM 

3 

INTEGRA CONTROL mobile application 

  Operating the alarm system from mobile devices: 

  control of the alarm system, 

  checking the alarm system status. 

  Configuring the alarm system from mobile devices. 

  Communication between the INTEGRA CONTROL application and the module can be 

established simply and easily with the SATEL connection setup service. 

Configuring the alarm system 

  Remote configuration of the alarm system via GPRS from a computer with DLOADX 

program installed. 

Managing the alarm system 

  Remote managing of the alarm system via GPRS from a computer with GUARDX program 

installed. 

Module firmware update 

  Updating the firmware via a computer connected to the RS-232 port of the control panel. 

  Updating the firmware via GPRS communication and the U

P

S

ERV

 update server (remote 

update). 

Interaction with the ETHM-1 Plus Ethernet module 

  GPRS used as backup communication path for Ethernet network. 

  Defining priority for different paths of event reporting (Ethernet, GPRS and SMS). 

  Dual Path Reporting compliant with EN 50136. 

Electronics board 

  RS-485 port to enable connection of INT-GSM module to ETHM-1 Plus module. 

  Communication bus for connection of INT-GSM module to keypad bus of the alarm control 

panel. 

  RS-232 port to allow: 

 connection to the RS-232 port of the alarm control panel (required for remote 

configuration from the DLOADX program and recommended for remote administration 
from the GUARDX program), 

  computer to be connected for the module firmware update. 

  LEDs indicating the module status. 

  Powering with 12 V DC (±15%). 

Summary of Contents for INT-GSM












































Reviews:

No comments