manualshive.com logo in svg

Satel INT-GSM, Manual, Page: 11 / 43

Share
Download
Satel INT-GSM Manual Download Page 11

SATEL INT-GSM 

9 

If the module is to be used in conjunction with the ETHM-1 Plus module (firmware version 
2.05 or newer required), connections between the modules and the control panel must be 
made as shown in Fig. 7. 

4.5  Starting the module 

1.  Power up the alarm system. 
2. Start the identification function in the control panel (see the control panel installer 

manual). If the module is connected to the alarm control panel, it will be identified as 
“INT-GSM”. If the module is connected to the ETHM-1 Plus module, “ETHM+-GSM” 
(instead of “ETHM-1”) will appear on the list of devices. 

3.  Configure the module (see „Configuring the module settings”). If PIN code(s) is / are 

required by the SIM card(s), use the DLOADX program to program the code(s) (see 
p. 12). 

4.6  Installing the SIM cards 

You can install up to two nano-SIM cards in the module. 
1.  Power down the alarm system. 
2.  Insert the SIM card / cards into the socket / sockets (Fig. 8). 
3.  Power up the alarm system. Logging the telephone into the GSM network may take a few 

minutes.  

If the module is to send data in GPRS technology, it is recommended that you use SIM 
cards with a dedicated tariff plan for M2M (machine-to-machine) communication. 

If the programmed PIN code is invalid, the module will report a trouble. Another 
attempt to use the PIN code will be made after 4 minutes. After the third attempt to use 
an invalid PIN code, the SIM card will be blocked. To unblock the SIM card, remove it 
and insert into a mobile phone. Then, enter the PUK code. 

 

 

Fig. 8. Installing the nano-SIM card. 

 

5.  Configuring the module settings 

You can configure the module settings using: 

  DLOADX program: “Structure” window 

“Hardware” tab 

“Keypads” branch 

[ module 

name]

 (Fig. 9), 

 LCD keypad: 

S

ERVICE MODE

 

S

TRUCTURE

 

H

ARDWARE

 

LCD

 KEYPADS

 

S

ETTINGS

 

[module name]

. 

All settings you can configure only by means of the DLOADX program. 

Names of parameters and options from the DLOADX program are used in this manual. When 
a parameter or an option is described, you will find in the square brackets their name 
displayed on the keypad. 

Summary of Contents for INT-GSM












































Reviews:

No comments