manualshive.com logo in svg

Satel INT-GSM, Manual, Page: 14 / 43

Share
Download
Satel INT-GSM Manual Download Page 14

12 INT-GSM 

SATEL 

SATEL server 

Connection via Satel server

 [SATEL server] – if this option is enabled, connection can be 

established via the SATEL server (Connection Setup Service). 

Push notifications

 [PUSH messages] – if this option is enabled, the INTEGRA CONTROL 

application can provide information about alarm system events by means of push 
notifications. The option is available if communication with SATEL server is enabled in the 
module. 

Information 

IMEI

 – individual identification number of the GSM telephone. 

ID

 – individual ID number assigned to the INT-GSM module by the SATEL server. 

If the module is to be used in another alarm system, the hitherto used ID number must 
be deleted. You should do it after connecting the module to the new control panel and 
establishing connection with the SATEL server, using the C

HANGE 

ID function available 

from the keypad (

S

ERVICE MODE

 

S

TRUCTURE

 

H

ARDWARE

 

 

LCD

 KEYPADS

 

 

S

ETTINGS

 

[module name]

 

C

HANGE 

ID). Having deleted the old ID number, the 

module will receive a new one. The INTEGRA CONTROL applications using the old ID 
number will be unable to connect to the control panel. 

[GSM signal]

 – information about GSM signal level. 

 – click the button to open the window in which the QR code is displayed. The QR code 

contains information required when configuring settings of communication through the 
SATEL server. You can read the QR code by using a mobile device or export to the file 
and transmit to the users. The QR code facilitates configuring the INTEGRA CONTROL 
application settings. 

Refresh

 – click to refresh all information. 

5.2  INT-GSM functions 

The settings configured in the “INT-GSM functions” tab are stored in the module 
memory. Before starting configuration, click on the “Read” button, and after completing 
it, click on the “Write” button. These settings will not be read / written after you click on 

the 

 button in the main menu of DLOADX program. 

Buttons 

Read 

– click to read the settings from the module. 

Write 

– click to write the settings to the module. 

Quit

 – click to cancel reading or writing the settings. 

Reset

 – click to delete the settings (and restore factory default settings). 

5.2.1  GSM phone 

SIM 1 / SIM 2 

PIN

 – PIN code of the SIM card.  

If an incorrectly programmed PIN code is used, the module will report a trouble. After 
the third attempt to use a wrong PIN code, the SIM card will be blocked. To unblock 
the SIM card, remove it and insert into a mobile phone. Then, enter the PUK code. 

GPRS APN

 – access point name for Internet GPRS connection. 

Username

 – user name for Internet GPRS connection. 

Summary of Contents for INT-GSM












































Reviews:

No comments