manualshive.com logo in svg

Sanwa ExzesX, Operating Manual, Page: 56 / 68

Share
Download
Sanwa ExzesX Operating Manual Download Page 56

Page 56

FUncTiOn PagE F3

5)  Move  the  throttle  control  stick  completely  back,  then  move  the  throttle 

control  stick  completely  forward.  Release  the  throttle  control  stick. The 

amount of travel will be indicated at the ends of the bar graph.

The  numbers  displayed  at 

the  ends  of  the  bar  graph 

will differ greatly. This is normal. 

The  throttle  control  stick  Brake 

side  moves  approximately  one-

half the distance that the throttle 

control stick High side.

4)  Move the steering control stick completely to the left, then move the steering 

control stick completely to the right. Release the steering control stick. 

The amount of travel will be indicated at the ends of the bar graph.

The  numbers  displayed  at 

the  ends  of  the  bar  graph 

may differ slightly. This is normal.

1)  Move both control sticks to their stops in each direction and check to ensure 

that the shaded area of each bar graph reaches the End Points. If one or 

more of the bar graphs come up short of their End Points when the control 

sticks are moved to their stops, recalibrate the control sticks again.

2)  Move both control sticks to their stops in each direction and check to 

ensure that the shaded area of each bar graph do not extend past the End 

Points. If one or more of the bar graphs extend past their End Points when 

the control sticks are moved to their stops, OVER will be displayed. If this 

occurs, recalibrate the control sticks again.

For the VR ADJUSTMENT Process to EXECUTE without an ERROR 

message,  you  MUST  complete  steps  4  and  5  correctly. If you only 

complete step 4 or step 5, or if you don't move the control sticks to their stops, 

the VR ADJUSTMENT process will not EXECUTE.

6)  Press the ENTER key. ADJUSTMENT EXECUTE? YES=<INC> NO=<DEC> 

will be displayed in the Programming Window.

7)  Press  the  INC/+  key  to  Execute  the  VR ADJUSTMENT  process. 

EXECUTING! will be displayed in the Programming Window.

To Cancel the VR ADJUSTMENT process, press the DEC/- key.

Verifying VR Adjustment Values

After the VR ADJUSTMENT process has been Executed successfully, it's important to double-check that the control sticks are 

operating properly.

Summary of Contents for ExzesX





































































Reviews:

No comments