manualshive.com logo in svg

Sanwa ExzesX, Operating Manual, Page: 28 / 68

Share
Download
Sanwa ExzesX Operating Manual Download Page 28

Page 28

Forward DELAY Setting

1)  Press  the  ENTER  key  to  move  the  cursor  to  DELAY,  then  press the 

INC/+ or DEC/- keys to set the desired DELAY percentage value.

TR-CTL FWD DELAY setting range is 0% to 100%. The default setting is 0%. 

The DELAY setting controls when the servo performs its function.

Forward POINT Setting

1)  Press the ENTER key to move the cursor to POINT, then press the INC/+ 

or DEC/- keys to set the desired POINT percentage value.

TR-CTL FWD POINT setting range is 5% to 100%. The default setting is 

50%. The POINT setting locates the actual point in the servo movement 

that you want the Traction Control function to deactivate.

The Traction Control function applies only in the range from Neutral to 

the POINT setting position.

[FWD] FORWARD TRACTION CONTROL

Forward Traction Control changes the Traction Control settings when the throttle control stick is moved from the Neutral to the 

throttle High side. There is no traction control setting for the throttle Brake side.

POINT

(5% to 100%)

Neutral

High

TR-CTL FWD TRACTION setting range is 1% to 100%. The default setting is 1%. The TRACTION setting adjusts the hold 

time before the servo moves.

Forward TRACTION Setting

1)  Press the Function key to highlight the TR-CTL menu. [FWD] will be Active 

in the Programming Window and the cursor will default to TRACTION.

2)  Press the INC/+ or DEC/- keys to set the desired TRACTION percentage 

value.

Forward ACT/INH Setting

1)  To use the TR-CTL FWD function, it must be Activated. Press the ENTER 

key to move the cursor to TR-CTL, then press the INC/+ or DEC/- keys to 

either ACT (Activate) or INH (Inhibit) the TR-CTL FWD function.

The TR-CTL FWD ACT/INH setting can be assigned to any Push-Button 

switch,  using  the  Key Assign  function.  For  more  information,  see 

page 49. By using this function, switching Traction Control ON or OFF can be 

selected during model operation.

Increasing the TRACTION percentage value, combined with the DELAY percentage value, creates a stepped acceleration 

through the servo's movement up to the POINT setting.

FUncTiOn PagE F1

Summary of Contents for ExzesX





































































Reviews:

No comments