manualshive.com logo in svg

Sanwa ExzesX, Operating Manual, Page: 36 / 68

Share
Download
Sanwa ExzesX Operating Manual Download Page 36

Page 36

If the transmitter is set to 2CH Mode, only ST and TH will be shown in the Programming Window.

The Servo Reversing function allows you to electronically switch the direction of servo 

travel. For example, if you move the steering control stick to the right, and the steering 

servo moves to the left, you can use the Servo Reversing function to make the steering 

servo move to the left. The Servo Reversing function is available for all four channels.

FUncTiOn PagE F2

Setting the Countdown Timer

1)  Press  the  ENTER  key  to  move  the  cursor  to  00',  then  press  INC/+  or 

DEC/- keys to set the desired Countdown Time in Minutes.

2)  Press  the  ENTER  key  to  move  the  cursor  to  00",  then  press  INC/+  or 

DEC/- keys to set the desired Countdown Time in Seconds.

3)  Press the ENTER key to move the cursor to 00, then press INC/+ or DEC/- 

keys to set the desired Countdown Time in 1/10th seconds.

Starting the Countdown Timer

1)  To start the Countdown Timer, press the Countdown Timer Switch. In the default configuration, the Countdown Timer Switch 

is assigned to Sw3. The Countdown Timer will start counting down from the preset time. When the Countdown Timer is 

within 10 seconds of zero, an audible tone will sound at 1 second intervals. When the Countdown Timer expires, a long 

audible tone will sound and the Count Up Timer function begins automatically. In Count Up mode, an audible tone will sound 

in 1 minute intervals. Pressing the Countdown Timer Switch a second time will reset the Countdown Timer and it will begin 

counting down again.

The Countdown Timer function can be assigned to any Push-Button switch, using the Key Assign function. For more 

information, see page 49.

Stopping the Countdown Timer

1)  The Countdown Timer can be stopped using two different methods:

A) By pressing and holding the Countdown Timer Switch for 3 seconds.
B) By pressing the INC/+ and DEC/- keys at the same time.

When the Countdown Timer is stopped, the Countdown Timer function is automatically turned OFF. To turn the Countdown 

Timer function back ON, see the Turning On the Countdown Timer section on the previous page.

TIMER DOWN setting range is 0' 00'' 00 to 99' 59' 90. The default setting is 00' minutes, 00" seconds, and 00 1/10th seconds.

Function Page 2 (REV)

1)  Press the Function key to highlight the REV menu. [ST] will be Active in 

the Programming Window.

2)  Press INC/+ or DEC/- keys to set the direction of servo travel.

REV setting range is NOR/REV. The default setting is NOR.

3) Adjust the remaining Servo Reversing settings using the same techniques.

REv (SERvO REvERSing)

Summary of Contents for ExzesX





































































Reviews:

No comments