manualshive.com logo in svg

Sanwa ExzesX, Operating Manual, Page: 48 / 68

Share
Download
Sanwa ExzesX Operating Manual Download Page 48

Page 48

FUncTiOn PagE F3

Audio Signal Sound Pre-Alarm Tone Setting

1)  Press the ENTER key to move the cursor to the left side PRE-ALM setting, 

then press the INC/+ or DEC/- keys to adjust the desired Tonal value for 

the first half PRE-ALM setting.

2)  Press the ENTER key to move the cursor to the right side PRE-ALM setting, 

then press the INC/+ or DEC/- keys to adjust the desired Tonal value for 

the second half PRE-ALM setting.

SIGNL PRE-ALM setting range is MUTE to S10. The default setting is S10. When changes are made to the Tonal settings, the 

currently selected Tone is sounded. The Pre-Alarm Tone setting affects the Lap Timer.

Audio Signal Sound Interval Timer Minutes Tone Setting

1)  Press the ENTER key to move the cursor to the left-side INT-T1 setting, 

then press the INC/+ or DEC/- keys to adjust the desired Tonal value for 

the first half INT-T1 setting.

2)  Press the ENTER key to move the cursor to the right-side INT-T1 setting, 

then press the INC/+ or DEC/- keys to adjust the desired Tonal value for 

the second half INT-T1 setting.

SIGNL INT-T1 setting range is MUTE to S10. The default setting is S10. When changes are made to the Tonal settings, the 

currently selected Tone is sounded. The INT-T1 Tone setting affects the Minutes portion of the Interval Timer.

Audio Signal Sound Interval Timer Seconds Tone Setting

1)  Press the ENTER key to move the cursor to the left-side INT-T2 setting, 

then press the INC/+ or DEC/- keys to adjust the desired Tonal value for 

the first half INT-T2 setting.

2)  Press the ENTER key to move the cursor to the right-side INT-T2 setting, 

then press the INC/+ or DEC/- keys to adjust the desired Tonal value for 

the second half INT-T2 setting.

SIGNL INT-T2 setting range is MUTE to S10. The default setting is S08. When changes are made to the Tonal settings, the 

currently selected Tone is sounded. The INT-T2 Tone setting affects the Seconds portion of the Interval Timer.

Audio Signal Sound Countdown Tone Setting

1)  Press the ENTER key to move the cursor to the left side DOWN setting, 

then press the INC/+ or DEC/- keys to adjust the desired Tonal value for 

the first half DOWN setting.

2)  Press the ENTER key to move the cursor to the right side DOWN setting, 

then press the INC/+ or DEC/- keys to adjust the desired Tonal value for 

the second half DOWN setting.

SIGNL DOWN setting range is MUTE to S10. The default setting is S05. When changes are made to the Tonal settings, the 

currently selected Tone is sounded. The DOWN Tone setting affects the Countdown Timer.

Summary of Contents for ExzesX





































































Reviews:

No comments