manualshive.com logo in svg

Sanwa ExzesX, Operating Manual, Page: 42 / 68

Share
Download
Sanwa ExzesX Operating Manual Download Page 42

Page 42

FUncTiOn PagE F2

Compensation Mixing Offset Setting

The OFFSET function allows you to shift and hold the neutral position of the SLAVE servo independent from the MASTER servo. It 

is useful to center the SLAVE servo or to shift the SLAVE servo's neutral position to change the starting point of your mix. 

Amount of

Deviation

When trim deviation appears 

in the graph with the steering 

in the neutral position.....

Adjust OFFSET value to move 

the  vertical  axis  and  erase 

the deviation bar graph.

By adjusting to the point where 

the  deviation  disappears,  the 

steering  neutral  position  can 

become the origin for Mixing.

Choosing the Master Channel

1)  Press the Function key to highlight the C-MIX menu. [C-MIX1] will be 

Active in the Programming Window and the cursor will default to ST1.

2)  Press the INC/+ or DEC/- keys to choose which channel you want to be 

the MASTER. Choose from either ST1, ST2, TH1, TH2, AUX1, AUX2.

Compensation Mixing Master Channel L/R Mixing Setting

1)  Press the ENTER key to move the cursor to MASTER L (MASTER H if 

TH or AUX is selected), then press the INC/+ or DEC/- keys to adjust the 

desired Mixing percentage value.

2)  Press the ENTER key to move the cursor to MASTER R (MASTER B or 

MASTER L if TH or AUX is selected), then press the INC/+ or DEC/- keys 

to adjust the desired Mixing percentage value.

C-MIX1 MASTER L/R setting range is -150% to 150%. The default setting is 0%. The Mixing percentage value is the percentage 

that the SLAVE servo will travel in proportion to the MASTER servo. For example, if ST1 L is set to 50%, when the steering 

control stick is moved to the left, the SLAVE servo  (TH in the example above) will travel half the amount that the steering servo 

travels. Using a positive or a negative percentage value determines the direction that the SLAVE servo travels in relation to the 

MASTER servo when the mix is Active. This mix is Linear.

Choosing the Slave Channel

1)  Press  the  ENTER  key  to  move  the  cursor  to  SLAVE,  then  press  the 

INC/+ or DEC/- keys to choose which channel you want to be the SLAVE. 

Choose from either ST, TH, AUX, or BR.

When the MASTER and SLAVE are set to the same channel, mixing 

takes  place  within  the  channel  itself.  This  causes  servo  travel 

to increase for positive percentage values and servo travel to decrease for 

negative percentage values.

[C-MIX1] COMPENSATION MIXING 1

Follow the steps below to program C-MIX1.

Summary of Contents for ExzesX





































































Reviews:

No comments