manualshive.com logo in svg

Sanwa ExzesX, Operating Manual, Page: 47 / 68

Share
Download
Sanwa ExzesX Operating Manual Download Page 47

Page 47

FUncTiOn PagE F3

SET-UP MOD CHANNEL setting range is 2 and 4. The default setting is 4 when using FH3 and FH3F modulation, and 2 when 

using FH2 modulation. Selecting 2 will enable 2-channel operation (Steering and Throttle). Selecting 4 will enable 4-channel 

operation (Steering, Throttle, 3rd Channel Auxiliary, and 4th Channel Brake).

Using the SHR setting with Digital servos will increase the servo's response time, even above the manufacturer's stated 

specification. This setting has no influence when used with Analog servos. Servo Mode settings are not available when 

using FH2 Modulation.

SHR Servo Mode Setting

1)  Press the ENTER key to move the cursor to ST, then press the INC/+ or 

DEC/- keys to set the desired Steering Servo Mode value.

SET-UP MOD ST setting range is NOR and SHR. The default setting is 

NOR. NOR can be used with both Analog and Digital servos. SHR is used 

only with Digital servos to give them a faster response time.

2)  Adjust the remaining Servo Mode settings using the same techniques.

[BIND] TRANSMITTER AND RECEIVER BINDING

Please refer to page 15 for instructions regarding transmitter and receiver Binding.

The Audio Signal Sound function allows you to set the audible key tones and audio 

alarm tones independently, and in different tonal scale. Tonal scale of each key press 

or alarm can be set differently for separate parts. For example, the tonal scale can be 

set separately for the first half (left side programming values) and the second half (right 

side programming values) of a tone, making it easier to differentiate between the two 

halves. Tones can be selected from among 10 different tones, providing a total of 100 pattern combinations for the first half 

and last half of signals.

Function Page 3 (SIGNL)

Audio Signal Sound Command Tone Setting

1)  Press  the  Function  key  to  highlight  the  SIGNL  menu.  The  cursor  will 

default to the left side COMMAND setting.

2)  Press the INC/+ or DEC/- keys to adjust the desired Tonal value for the 

first  half  (left  side)  COMMAND  setting,  then  press  the  ENTER  key  to 

move the cursor to the right side COMMAND setting and press the INC/+ 

or  DEC/-  keys  to  adjust  the  desired  Tonal  value  for  the  second  half 

(right side) COMMAND setting.

SIGNL COMMAND setting range is MUTE to S10. The default setting is S10. When changes are made to the Tonal settings, 

the currently selected Tone is sounded. The Command Tone setting affects the Programming Keys.

If you do not want to hear a Signal Tone, select MUTE for both tones. If you mute only one tone, the other half of the tone will 

sound. The Audio Icon      displayed in the Information Window will change to        if both Command Tone settings are Muted.

SignL (aUDiO SignaL SOUnD)

Modulation Channel Setting (FH2 Modulation Only)

If FH2 Modulation is chosen, you can choose to operate the transmitter in 

either 2CH Mode or 4CH Mode. 

1)  Press the ENTER key to move the cursor to CHANNEL, then press the 

INC/+ or DEC/- keys to set the desired Channel value.

This option can only be changed when TYPE FH2 is chosen. It cannot 

be changed if using FH3 or FH3F modulation.

FuNCTION P

AGE F3

Summary of Contents for ExzesX





































































Reviews:

No comments