manualshive.com logo in svg

Sanwa ExzesX, Operating Manual, Page: 21 / 68

Share
Download
Sanwa ExzesX Operating Manual Download Page 21

Page 21

FUncTiOn PagE F1

[TH] THROTTLE EXPONENTIAL

Throttle Exponential can be adjusted from Mild, Linear and Quick. In general, reduce the Exponential value on a slippery track or 

with a model that has a higher-torque motor or engine. Increase the Exponential value on a high-grip track or with a model that 

has a lower-torque motor or engine.

The throttle High side and the throttle Brake side can be set independently.

EXP TH-H setting range is between -100% (Mild) to 100% (Quick). The default setting is 0% (Linear).

EXP TH-B setting range is between -100% (Mild) to 100% (Quick). The default setting is 0% (Linear).

Throttle ACT/INH Setting

1)  To use the Throttle Exponential function, it must be Activated. Press the 

ENTER key to move the cursor to EXP, then press the INC/+ or DEC/- 

keys to either ACT (Activate) or INH (Inhibit) the Exponential function.

The EXP TH ACT/INH setting can be assigned to any Push-Button switch using the Key Assign function. For more information, 

see page 49. By using this function, switching Exponential ON or OFF can be selected during model operation.

Steering ACT/INH Setting

1)  To use the Steering Exponential function, it must be Activated. Press the 

ENTER key to move the cursor to EXP, then press the INC/+ or DEC/- 

keys to either ACT (Activate) or INH (Inhibit) the Exponential function.

The  EXP  ST  ACT/INH  setting  can  be  assigned  to  any  desired 

Push-Button switch using the Key Assign function. For more information, 

see page 49. By using this function, switching Exponential ON or OFF can be 

selected during model operation.

Throttle High Side Setting

1)  Press the Function key to move the cursor to [TH] in the EXP Programming 

Window. The cursor will default next to H.

2)  With the cursor at H (throttle High), press the INC/+ or DEC/- keys to set 

the desired Exponential percentage value for the throttle High side.

Throttle Brake Side Setting

1)  Press  the  ENTER  key  to  move  the  cursor  to  B,  then  press  the  INC/+ 

or DEC/- keys to set the desired Exponential percentage value for the 

throttle Brake side. 

FuNCTION P

AGE F1

Summary of Contents for ExzesX





































































Reviews:

No comments