manualshive.com logo in svg

Sanwa ExzesX, Operating Manual, Page: 11 / 68

Share
Download
Sanwa ExzesX Operating Manual Download Page 11

Page 11

USing Li-PO OR Li-FE BaTTERiES

l

  Use 

ONLY

 a 2 Cell Li-Po or Li-Fe battery pack of desired capacity. 

DO NOT uSE A 3 CELL LI-PO OR LI-FE BATTERY PACK

 

or the transmitter and/or receiver will be damaged.

 

l

  Do NOT charge your battery through the transmitter using the Charging Jack. The battery 

MuST

 be removed from the 

transmitter for charging or the transmitter could be damaged.

l

  Use a charger specifically designed to charge Li-Po or Li-Fe batteries.

l

  When changing the connector on your battery to match the battery power plug in the transmitter (or 

on the receiver switch harness), please observe correct polarity. Connecting with reverse polarity 

will damage the transmitter and/or receiver.

l

  Observe all safety precautions provided with your Li-Po or Li-Fe battery before and during use, and during the charging process.

l

  Damage to the transmitter and/or receiver caused by improper use, wrong battery type, or reverse polarity will not be covered 

under warranty.

-   =  Negative (Black)

+  =  Positive (Red)

Tx anD Rx OPTiOnS anD cOnnEcTiOnS

TRanSMiTTER anD REcEivER BaTTERY OPTiOnS

Instead of using Alkaline batteries to power the transmitter and receiver, you can use individual rechargeable Ni-Cd or Ni-MH 

batteries, or you can use a 2 cell Li-Po, or a 2 cell Li-Fe battery pack. Either option will provide longer usage time and reduced 

cost in the long run, since you won't need to continuously purchase new Alkaline batteries.

The 

EXZES 

X

 2.4GHz FHSS-3

 transmitter features a Charging Jack, which can be used with the optional Sanwa 95035 AC 

Transmitter Charger to recharge Ni-Cd or Ni-MH the batteries without removing them from the transmitter. For more information on 

the use and charging of Li-Po and Li-Fe battery packs, see the Using Li-Po or Li-Fe Batteries section below.

1)   Install optional 1200mAh or greater Ni-MH rechargeable batteries (available separately) into the transmitter, following the 

steps in the Transmitter Battery Installation section on the previous page.

Charging Optional Ni-Cd or Ni-MH Transmitter Batteries

WARNING

  Do NOT attempt to recharge Alkaline batteries. Do not use the Charging Jack with a fast charger or Peak-Detection 

charger or the transmitter could be damaged.

WARNING

  Use 

ONLY

 the recommended optional Sanwa 95035 AC Transmitter Charger or damage to the transmitter could 

result. An after-market peak-detection charger and/or cycler should NOT be used to charge Ni-Cd or Ni-MH rechargeable 

batteries through the transmitter. The circuitry within the transmitter can interfere with the peak-detection charger's normal 

operation, resulting in over-charging and damaging the batteries, and possibly the transmitter itself. A peak-detetction charger 

can be used, but ONLY if the batteries are charged outside of the transmitter.

1)  Plug the Sanwa 95035 AC Transmitter Charger into a 110v ~ 240v AC power outlet.

2)  Plug the round connector from the charger into the Charging Jack in the transmitter. The charger LED will illuminate red, 

indicating that the charger is charging. When the charging process completes, the charger LED will turn green.

3)  The charger output is 150mAh, therefore, it will take approximately 8 hours to recharge fully-discharged 1200mAh 

batteries (1200/150=8). Charge time will vary depending on the mAh capacity of the batteries you're charging. For example, 

2200mAh batteries would require a 15 hour charge (2200/150=14.6).

l

 

Before charging the batteries, double-check that the transmitter is turned OFF.

l

 

Overcharging reduces the life of the batteries and can result in overheating and bursting. This may cause personal injury 

and/or property damage.

l

 

Do not plug the recommended charger into anything other than a 110v ~ 240v AC power outlet. Plugging the charger into 

anything other than a 110v ~ 240v AC power outlet may result in smoking, sparks, or fire.

l

 

Do not throw the batteries or abuse them in any manner.  Do not dispose of the batteries in the fire or allow it to overheat.

l

 

Do not short-circuit the battery terminals with wire or any other object.

This section describes recharging only optional Ni-Cd or Ni-MH transmitter batteries using he Sanwa 95035 AC Transmitter 

Charger. If you use  Ni-Cd or Ni-MH batteries for the receiver, or a Ni-Cd, Ni-MH, Li-Po, or Li-Fe receiver battery pack, you 

will need to use a different type of charger. For more information and charger recommendations, visit your local hobby retailer.

GENERAL

Summary of Contents for ExzesX





































































Reviews:

No comments