manualshive.com logo in svg

Sanwa ExzesX, Operating Manual, Page: 35 / 68

Share
Download
Sanwa ExzesX Operating Manual Download Page 35

Page 35

FUncTiOn PagE F2

[DOWN] COuNTDOWN TIMER

The Countdown Timer function can be used to notify you of your model’s running time. For example, you can set the Countdown 

Timer to alert you when it's time to refuel. When the Countdown Timer expires, a long audible tone will sound and the Count Up 

Timer function begins automatically. This allows you to check the time elapsed since the Countdown Timer ran out. In Count Up 

mode, an audible tone will sound in 1 minute intervals.

Setting Interval Timer One (T1)

1)  Press the ENTER key to move the cursor to T1 00', then press INC/+ or 

DEC/- keys to set the desired Interval Time in Minutes. Next, press the 

ENTER key to move the cursor to T1 00", then press INC/+ or DEC/- keys 

to set the desired Interval Time in Seconds.

TIIMER INT T1 setting range is 00' 00" to 99' 59". The default setting is 

00' minutes and 00" seconds.

Setting Interval Timer Two (T2)

1)  Press the ENTER key to move the cursor to T2 00", then press INC/+ or 

DEC/- keys to set the desired Interval Time in Seconds. Next, press the 

ENTER key to move the cursor to T2 00, then press INC/+ or DEC/- keys 

to set the desired Interval Time in 1/10th seconds.

TIIMER INT T2 setting range is 00" 00 to 59" 90. The default setting is 00" 

seconds and 00 1/10th seconds.

Starting the Interval Timer(s)

1)  To start the Interval Timer(s), press the Interval Timer Switch. In the default configuration, the Interval Timer Switch is 

assigned to Sw3. Both Interval Timers (if programmed) will start counting up. When Interval Timer T2 reaches the preset 

time an audible tone will sound and it will reset and begin counting up from zero. When Interval Timer T1 reaches the preset 

time, a different audible tone will sound and it will reset and begin counting up from zero. Pressing the Interval Timer Switch 

a second time will reset the Interval Timer(s) and they will begin counting up from zero again.

The Interval Timer function can be assigned to any Push-Button switch, using the Key Assign function. For more information, 

see page 49.

Stopping the Interval Timer(s)

1)  The Interval Timer(s) can be stopped using two different methods:

A) By pressing and HOLDING the Interval Timer Switch for 3 seconds.

 

B)  By pressing the INC/+ and DEC/- keys at the same time.

When the Interval Timer(s) are stopped, the Interval Timer function is automatically turned OFF. To turn the Interval Timer 

function back ON, see the Turning On the Interval Timers section on the previous page.

Turning On the Countdown Timer

1)  Press the Function key to move the cursor to [DOWN] in the Programming 

Window. The cursor will default to OFF.

2)  Press INC/+ or DEC/- keys to turn the Countdown Timer ON.

FuNCTION P

AGE F2

Summary of Contents for ExzesX





































































Reviews:

No comments