manualshive.com logo in svg

Sanwa ExzesX, Operating Manual, Page: 23 / 68

Share
Download
Sanwa ExzesX Operating Manual Download Page 23

Page 23

FUncTiOn PagE F1

[TH] THROTTLE ADJuSTABLE RATE CONTROL

Throttle Adjustable Rate Control can be adjusted from Mild, Linear and Quick. In general, reduce the Adjustable Rate Control 

value on a slippery track or with a model that has a higher-torque motor or engine. Increase the Adjustable Rate Control value on 

a high-grip track or with a model that has a lower-torque motor or engine.

The throttle High side and the throttle Brake side can be set independently.

Throttle RATE Setting

1)  Press the Function key and move the cursor to [TH] in the ARC Programming 

Window. The cursor will default to RATE.

2)  To  adjust  the  throttle  High  side  setting,  push  the  throttle  control  stick 

forward. The cursor will point to the left. Press the INC/+ or DEC/- keys to 

set the desired RATE value.

ARC TH RATE setting range is between -100% (Mild) to 100% (Quick). The default setting is 0% (Linear).

Throttle POINT Setting

1)  Press the ENTER key to move the cursor to POINT.

2)  To  adjust  the  throttle  High  side  setting,  push  the  throttle  control  stick 

forward. The cursor will point to the left. Press the INC/+ or DEC/- keys to 

set the desired POINT value.

3)  To adjust the throttle Brake side setting, pull the throttle control stick back. 

The cursor will point to the right. Press the INC/+ or DEC/- keys to set the 

desired POINT value.

ARC TH POINT setting range is between 5 to 95. The default setting is 50.

Steering ACT/INH Setting

1)  To use the Steering Adjustable Rate Control function, it must be Activated. 

Press the ENTER key to move the cursor to ARC then press the INC/+ or 

DEC/- keys to either ACT (Activate) or INH (Inhibit) the Adjustable Rate 

Control function.

The ARC  ST ACT/INH  setting  can  be  assigned  to  any  Push-Button 

switch  using  the  Key  Assign  function.  For  more  information,  see 

page  49.  By  using  this  function,  switching Adjustable  Rate  Control  ON  or 

OFF can be selected during model operation.

Throttle ACT/INH Setting

1)  To use the Adjustable Rate Control function, it must be Activated. Press 

the ENTER key to move the cursor to ARC, then press the INC/+ or DEC/- 

keys to either ACT (Activate) or INH (Inhibit) the Adjustable Rate Control 

function.

The ARC  TH ACT/INH  setting  can  be  assigned  to  any  Push-Button 

switch,  using  the  Key Assign  function.  For  more  information,  see 

page 49. By using this function, switching Adjustable Rate Control ON or OFF 

can be selected during model operation.

3)  To adjust the throttle Brake side setting, pull the throttle control stick back. The cursor will point to the right. Press the INC/+ 

or DEC/- keys to set the desired RATE value.

FuNCTION P

AGE F1

Summary of Contents for ExzesX





































































Reviews:

No comments