manualshive.com logo in svg

Sanwa ExzesX, Operating Manual, Page: 45 / 68

Share
Download
Sanwa ExzesX Operating Manual Download Page 45

Page 45

FUncTiOn PagE F3

The Transmitter Setup function allows you to change a number of custom options 

related to the function of the transmitter and its Multi-Function LCD. Transmitter and 

receiver Binding is also done through the Set-Up menu.

Function Page 3 (SET-uP)

SET-UP SYSTEM CONTRAST setting range is 0% to 100%. The default setting is 80%. Increasing the CONTRAST setting 

will make the Multi-Function LCD easier to read in bright sunlight. Higher CONTRAST settings will increase battery usage.

Changing the Multi-Function LCD Contrast Setting

1)  Press  the  Function  key  to  highlight  the  SET-UP  menu.  [SYSTEM]  will 

be Active in the Programming Window and the cursor will default to 

CONTRAST.

2)  Press  the  INC/+  or  DEC/-  keys  to  adjust  the  desired  CONTRAST 

percentage value.

Changing the Transmitter Vibrator Setting

1)  Press the ENTER key to move the cursor to VIBRATOR, then press the 

INC/+ or DEC/- keys to select the desired VIBRATOR value.

SET-UP SYSTEM VIBRATOR setting range is ACT and INH. The default 

setting is INH. When set to ACT, the transmitter will vibrate at the same time 

that the Timer alarms or the Low Voltage Alarm Activate. When set to 

INH, the transmitter will not vibrate when these alarms Activate.

Changing the ON Power Logo Setting

1)  Press the ENTER key to move the cursor to OP LOGO, then press the 

INC/+ or DEC/- keys to select the desired OP LOGO value.

SET-UP SYSTEM OP LOGO setting range is ACT and INH. The default 

setting is ACT. When set to ACT, the 

EXZES X

 logo will be displayed in the 

Programming Window during the Power ON process. When set to INH, no 

logo be displayed in the Programming Window during the Power ON process.

Changing the Multi-Function LCD Backlight Color Setting

1)  Press the ENTER key to move the cursor to LIGHT-COLOR, then press 

the INC/+ or DEC/- keys to select the desired LIGHT-COLOR value.

SET-UP SYSTEM LIGHT-COLOR setting range is WHITE and BLUE. The 

default  setting  is  WHITE.  When  set  to  WHITE,  the  Multi-Function  LCD 

backlight will be White. When set to BLUE, the Multi-Function LCD backlight 

will be Blue.

We recommend Activating the Vibrator function if you Inhibit the Audible Alarms. For more information, see page 45.

SET-UP (TRanSMiTTER SETUP)

[SYSTEM] SYSTEM uSER OPTIONS

The System function includes a number of options that the user can make adjustments to set the transmitter up to their specification 

and their liking.

FuNCTION P

AGE F3

Summary of Contents for ExzesX





































































Reviews:

No comments