manualshive.com logo in svg

Sanwa ExzesX, Operating Manual, Page: 40 / 68

Share
Download
Sanwa ExzesX Operating Manual Download Page 40

Page 40

FUncTiOn PagE F2

BR-MIX 3CH-BRAKE setting range is INH to ACT. The default setting is INH. When set to ACT, the 3rd channel brake servo is 

Activated and the 3CH DELAY percentage value can be set. When set to INH, the 3rd channel brake servo will not function.

Activating the 3CH (Channel 3) Brake

1)  Press  the  ENTER  key  to  move  the  cursor  to  3CH-BRAKE  in  the 

Programming Window, then press INC/+ or DEC/- keys to set the desired 

3CH-BRAKE value.

When you set the 3CH-BRAKE value to ACT, the 3CH DELAY option 

becomes available.

Brake Mixing 3CH (Channel 3 Brake) Delay Setting

1)  Press the ENTER key to move the cursor to 3CH in the Programming 

Window,  then  press  INC/+  or  DEC/-  keys  to  adjust  the  desired  3CH 

DELAY percentage value.

BR-MIX 3CH DELAY setting range is 0% to 100%. The default setting is 0%. 

The 3CH DELAY setting controls the speed of the 3rd channel brake servo. 

When the percentage value is increased the speed of the 3rd channel 

brake servo is slowed.

BR-MIX TH-BRAKE CUT setting range is INH to ACT. The default setting is INH. When set to ACT, the Brake side of the throttle 

servo will not function, but the 4th channel brake servo (and the 3rd channel brake servo if set to ACT) will continue to function. 

When set to INH, both the Brake side of the throttle servo and any separate Brake servos will function normally.

Brake Mixing TH-Brake Cut Setting

1)  Press the ENTER key to move the cursor to TH-BRAKE CUT in the 

Programming Window, then press INC/+ or DEC/- keys to set the desired 

TH-BRAKE CUT value.

The Throttle Brake Cut function should ONLY be set to ACT if you are 

using one or two separate brake servos. If you set the Throttle Brake 

Cut function to ACT while only using the 2nd channel brake (throttle/brake on 

the same servo), you will not have any brake function!

BRAKE MIXING WITH THE TRANSMITTER SET TO 2CH MODE

The Brake Mixing function can be used when the transmitter is set to 2CH Mode, although Brake Mixing functionality is highly 

reduced. The following Brake Mixing function settings are available in 2CH Mode:

Brake Mixing 2CH (Channel 2 Brake) Delay Setting

1)  Press the Function key to highlight the BR-MIX menu. The cursor will default to 2CH in the Programming Window.

2)  Press INC/+ or DEC/- keys to adjust the desired 2CH DELAY percentage value. This setting operates the same as the 2CH 

DELAY setting described in the Brake Mixing 2CH (Channel 2 Brake) Delay Setting section on the previous page.

Brake Mixing TH-Brake Cut Setting

1)  Press the ENTER key to move the cursor to TH-BRAKE CUT in the Programming Window.

2)  Press the INC/+ or DEC/- keys to either Activate or Inhibit the Throttle Brake Cut. This setting operates the same as the 

TH-BRAKE CUT setting described in the Brake Mixing TH-Brake Cut Setting section above.

Even when the transmitter is set to 2CH Mode, the 4th channel brake will function if you're using a 4 channel receiver.

Summary of Contents for ExzesX





































































Reviews:

No comments