manualshive.com logo in svg

Sanwa ExzesX, Operating Manual, Page: 18 / 68

Share
Download
Sanwa ExzesX Operating Manual Download Page 18

Page 18

FUncTiOn PagE F1

In order to set any functions for Auxiliary Channel 3, you must first change the channel setting from 2CH to 4CH. In the default 

configuration (FH3 Modulation), the transmitter is set to 4CH Mode. If you are using FH2 Modulation with an FHSS-2 receiver, 

the default configuration is 2CH Mode. For information on enabling 4CH Mode when using an FHSS-2 receiver, see page 47.

Auxiliary Channel 3 must first be assigned to a Trim switch or the Dial Knob. For more information, see page 50.

2)  Press the Function key to move the cursor to [3CH] in the EPA Programming 

Window.

3)  To  adjust  the  High  side,  turn  the  Dial  Knob  clockwise.  The  cursor  will 

move  next  to  100%H.  Press  the  INC/+  or  DEC/-  keys  to  increase  or 

decrease the amount of servo travel. To adjust the Low side, turn the Dial 

Knob counter-clockwise. The cursor will move next to 100%L. Press the 

INC/+ or DEC/- keys to increase or decrease the amount of servo travel.

EPA 3CH setting range is between 0% and 150% in either direction. The default setting is 100%.

2)  Press  the  Function  key  to  move  the  cursor  to  [3CH]  in  the  EPA 

Programming Window. The cursor will default next to 100%B. Press the 

INC/+ or DEC/- keys to increase or decrease the amount of servo travel.

EPA 3CH-B setting range is between 0% and 160% in the Brake direction. 

The default setting is 100%.

Trm5

Switch

[3CH] AuXILIARY CHANNEL 3 END POINT ADJuSTMENT - WITH 3CH BRAKE INHIBITED

With the BRAKE function Inhibited, Auxiliary Channel 3 can be used for functions such as remote needle valve control, transmission 

reverse, the Dig function on your rock crawler, and much more.

The EPA-B setting can be assigned to any 

desired trim switch using the Key Assign 

function. For more information, see page 50.

3)  Test-run your model to set the throttle Brake adjustment using 

the Trm5 switch. The Trm5 switch can be used to change the 

EPA-B setting without accessing the Programming Menu. Push 

the trim switch right to decrease the Brake EPA and pull the trim 

switch left to increase the Brake EPA. This is convenient if you 

need to change the Brake EPA setting while driving.

1)  Make sure that 4CH is selected in the SET-UP menu and that 3CH-BRAKE is set to INH in the BR-MIX menu. For more 

information, see pages 46 and 40.

[3CH] AuXILIARY CHANNEL 3 END POINT ADJuSTMENT - WITH 3CH BRAKE ACTIVE

When using Auxiliary Channel 3 as an additional BRAKE channel, the End Point Adjustment can be set separately from the 

Auxiliary Channel 4 BRAKE channel. In this configuration, the 3CH BRAKE is Activated using the throttle Brake function.

1)  Make sure that 4CH Mode is selected in the SET-UP menu and that 3CH-BRAKE is set to ACT in the BR-MIX menu. For 

more information, see pages 46 and 40.

3CH-B EPA POINT

Neutral

TH

3CH

TH-B EPA POINT

Summary of Contents for ExzesX





































































Reviews:

No comments