PRESSING
UP THE
STOP
RING
5.
Fit the engaging lever arm to the cog engaging ring
and insert the assembly, together with the rotor
into the drive
housing.
6.
Secure the engaging lever arm with its locating screw.
7.
Place the washers in the drive housing, first the steel
washer and then the rubber washer. The lips must
be turned towards the rotor.
8.
Fit the starter housing with the notches above the
guide pin and the lip of the rubber washer.
9.
Slip the steel washer and fiber washer over the rotor
shaft.
10.
Fit the brush plate.
Lift the brush springs with a
wire hook and
insert the brushes.
11.
Mount the commutator bearing housing with the
notches above the feed cable's rubber insulation.
12.
Fit the rubber gasket, shims and
U-washer.
13.
Locate the capsule bracket and secure it with the
two
screws.
14.
Insert and tighten the bearing housing screws.
15.
Check the axial play of the shaft 0.002—0.012 in.
(0.05—0.30 mm) and correct with shims if neces-
sary.
16.
Hook the solenoid to the engaging lever arm and
secure
with
the
two
screws.
17.
Connect the feeder cable.
18.
Test the starter
(see group 9 for specifications and
test
values).
SOLENOID SWITCH
Starter removed
Removal
1.
Disconnect supply cable.
2.
Remove the two retaining s
noid switch.
crews and then the sole-
Installation
1.
2.
3.
Hook solenoid switch in engaging lever and secure
With the two retaining screws.
Connect supply cable.
Test starter. See group 0, Specifications.
CARBON BRUSHES
Starter removed
Removal
1.
2.
3.
4.
9"
Remove the two screws from the capsule bracket.
Remove the capsule bracket, U-washer, shims and rub-
her gasket
(pas.
5—8).
Remove the screws from the commutator bearing hous-
ing
Remove the commutator bearing housing
Lift the brush springs from the holders with a wire
hook and take out the brushes.
Remove
the
brush
plate.
Unsolder
the
brush
wiring
connections
from
the
brush
plate and field winding.
51334
BRUSH
HOLDER
PLATE
AND
FIELD WINDING
1.
Brush
holder
plate
2.
Brush
3.
Brush,
negative
4.
Brush
spring
5. Starter housing
6.
Brush,
positive with field winding
7.
Field winding lead
Summary of Contents for 95 1967
