![background image](http://html1.mh-extra.com/html/ryobi/rcs1935b/rcs1935b_original-instructions-manual_1504208007.webp)
5
English
|
EN
FR
DE
ES
IT
NL
PT
DA
SV
FI
NO
RU
PL
CS
HU
RO
LV
LT
ET
HR
SL
SK
BG
UK
TR
1
2
1/3
2/3
When the log is supported on both ends, cut 1/3 the
diameter from the top (overbuck). Then make the
fi
nished
cut by underbucking the lower 2/3 to meet the
fi
rst cut.
2
1
2/3
1/3
When bucking on a slope always stand on the uphill side of
the log. To maintain control when “cutting through”, release
the cutting pressure near the end of the cut without relaxing
your grip on the chainsaw handles. Don’t let the chain
contact the ground. After completing the cut, wait for the
saw chain to stop before you move the chainsaw. Always
stop the motor before moving from tree to tree.
LIMBING A TREE
Limbing is removing the branches from a fallen tree. When
limbing, leave larger lower limbs to support the log o
ff
the
ground. Remove the small limbs in one cut. Branches
under tension should be cut from the bottom up to avoid
binding the chainsaw.
SPRINGPOLES
A springpole is any log, branch, rooted stump, or sapling
that is bent under tension by other wood so that it springs
back if the wood holding it is cut or removed.
On a fallen tree, a rooted stump has a high potential of
springing back to the upright position during the bucking
cut to separate the log from the stump. Watch out for
springpoles—they are dangerous. Do not attempt to cut
bent branches or stumps that are under tension unless you
are professionally trained and competent to do so.
WARNING!
Springpoles are dangerous and could strike
the operator, causing the operator to lose control of the
chainsaw. This could result in a severe or fatal injury to the
operator. Cutting spring poles should be done by trained
users.
TRANSPORTATION AND STORAGE
■
Turn off the product, disconnect it from the power
supply, and allow the product to cool down before
storing or transporting.
■
Remove all foreign material from the product. Store the
product in a cool, dry, and well-ventilated place that is
inaccessible to children. Keep the product away from
corrosive agents, such as garden chemicals and de-
icing salts. Do not store the product outdoors.
■
Fit the guide bar cover before storing the product or
during transportation.
■
For transportation, secure the product against
movement or falling to prevent injury to persons or
damage to the product.
MAINTENANCE
■
Use only original manufacturer’s replacement parts,
accessories, and attachments. Failure to do so
can cause possible injury, can contribute to poor
performance, and may void your warranty.
■
Servicing requires extreme care and knowledge
and should be performed only by a qualified service
technician. Have the product serviced by an authorised
service centre only.
■
You may make adjustments or repairs described in this
manual. For other repairs, have the product serviced by
an authorised service centre only.
■
Consequences of improper maintenance, removal, or
modification of safety devices, may cause the product
to not function correctly, increasing the potential
for serious injury. Keep the product professionally
maintained.
■
Sharpening the chain safely is a skilled task. Therefore,
the manufacturer strongly recommends that a worn or
dull chain is replaced with a new one, available at your
authorised service centre. The part number is available
in the product specification table in this manual.
■
Follow the instructions for lubricating and chain tension
checking and adjustment.
■
After each use, clean plastic parts with a soft, dry cloth.
■
Check all nuts, bolts, and screws at frequent intervals
for security to ensure that the product is in safe working
condition. Any part that is damaged should be properly
repaired or replaced by an authorised service centre.
Summary of Contents for RCS1935B
