
2–6 • Installation
UDC-8625A Series User Manual (Iss. 11)
UDC-8625A-B Rear Module
When installing the UDC-8625A-B in the DFR-8321 series frame or the OG3-FR series frames,
the following rear module is supported:
•
8320AR-052A
— This rear module provides one analog reference input, four SDI inputs,
four SDI outputs, four GPIOs, eight AES/EBU WECO™ connections, a serial port, and
an ethernet port. There is no bypass relay available on this rear module.
Installing the Card
If the rear module is already installed, proceed to the section “
To install the rear module in an openGear frame
1.
Ensure that the openGear frame is properly installed. Refer to the manual that
accompanied your frame for details.
2.
When installing the 8320AR-041 or 8322AR-065 rear module, use the following slot
combinations:
3.
When installing a
rear module other than the 8320AR-041 or 8322AR-065, use the
following slot combinations:
4.
Remove the Blank Plates from the rear of the selected card frame slots.
5.
Seat the bottom of the rear module in the seating slot at the base of the frame’s
backplane.
6.
Align the top hole of the rear module with the screw hole on the top-edge of the frame
backplane.
7.
Verify that the card aligns with the rear module before fully tightening any of the slot
screws.
8.
Using a Phillips screwdriver and the supplied screw, fasten the rear module to the
backplane. Do not over tighten.
9.
Ensure proper frame cooling and ventilation by having all rear frame slots covered with
rear modules or Blank Plates.
Caution
— Do not install the 8320AR-041 or 8322AR-065 rear module in slots 19
and 20 of the openGear frame. Doing so will damage the UDC-8625A, the Network
Controller card, or both.
Caution
— The 8322AR-065 rear module is only compatible with the OG3-FR
series frames. Installing this rear module in a frame other than the OG3-FR will
damage the rear module.
• Slots 1, 2,
• Slots 7, 8
• Slots 13, 14
• Slots 3, 4
• Slots 9, 10
• Slots 15, 16
• Slots 5, 6
• Slots 11, 12
• Slots 17, 18
• Slots 1, 2, 3, 4
• Slots 13, 14, 15, 16
• Slots 5, 6, 7, 8
• Slots 17, 18, 19, 20
• Slots 9, 10, 11, 12
Summary of Contents for Opengear UDC-8625A Series
