ROBOTIQ PALLETIZING SOLUTION AX Series Instruction Manual Download Page 44 | Manualshive

Page: 44 / 115

background image

Palletizing Solution - Instruction Manual

Inter-Controller Connections

1. Open the UR controller. Connect the USB hub to a USB port.

2. Connect the Ethernet/USB converter cable to a USB port.

3. Connect the Ethernet cable into the Ethernet socket on the top of the linear axis Controller.

4. Pass the other extremity of the cable through the hole under the UR controller and connect it into the Ethernet/USB converter

cable that is already connected.

Info

Follow cable management good practices. You can either drill a hole in the hole plug or use a grommet (not included).

Fig. 3-1: Linear Axis Controller Cable Summary

Safety Signal Connections

1. Take the signal safety cable and pass it through an opening under the UR controller.

2. Wire the cable by following the schema and the table available in the Appendix section.

Caution

l

Follow the installation guidelines in the UR manual for Emergency stop or Safeguard connections. Use the connector
supplied by Robotiq for Safeguard connections.

l

If the safeguard is not used, add jumpers between pin 1-2 and 3-4.

l

Do not forget to connect the safety reset wire (white color) according to your safety setup. For more details, please refer
to the table in the Safety Connections section.

44

«
...
42
43
44
45
46
...
»

Summary of Contents for PALLETIZING SOLUTION AX Series




















































































































Reviews:

No comments

Related manuals for PALLETIZING SOLUTION AX Series

Robotics Sensor Station IoT

Brand: fischertechnik Pages: 50

JMHZ2-16D-X7400B-TM

Brand: SMC Networks Pages: 25

Brand: Leju Robotics Pages: 18

Brand: Leju Robotics Pages: 42

Brand: ROBOPEC Pages: 4

Brand: XPROHELI Pages: 15

GRIPKIT CR PLUS

Brand: WEISS ROBOTICS Pages: 45

Brand: Prince Pages: 5

Brand: Prince Pages: 13

Brand: Prince Pages: 24

Play The Best T8561

Brand: Prince Pages: 24

Brand: Prince Pages: 38

Brand: Learning Resources Pages: 16

Brand: Kitronik Pages: 4

MOVE Motor Klaw

Brand: Kitronik Pages: 3

LINE FOLLOWING BUGGY V3

Brand: Kitronik Pages: 12

Brand: COVVI Pages: 83

Brand: COVVI Pages: 90

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands