ROBOTIQ PALLETIZING SOLUTION AX Series Instruction Manual Download Page 104

Page: 104 / 115

Error message:"Please use the
Safeguard reset before starting the
linear axis"

Power off and power on the Linear Axis
Controller.

Power off and power on the Linear
Axis Controller.

The cables of the Linear Axis are not
properly connected to the UR controller.

Inspect the connections. Please refer
to the Safety Connections section.

The "Safety configuration" and/or "System
Emergency Stopped" functions were not
configured correctly.

Verify that the "Safeguard reset" and
"System Emergency Stopped"
functions are configured correctly.

Installation tab > Safety > I/O

No safeguard measure is being used, but
none have been bypassed.

Even if the safeguard function is not
used, both the safeguard wire and
reset wire from the Linear Axis should
be connected to a 24V terminal block
in the UR controller (bypass).

Please refer to the Safety
Connections section for more
information.

A safeguarding OSSD is connected
directly to the robot.

OSSD signals are not compatible with
the Linear Axis (even if the e-Series
UR controller can be compatible).

A special relay is required to convert
OSSD signals to standard signals.

The emergency output from the UR
controller is set to OSSD signal.
(e-Series only)

Verify that the OSSD checkbox for the
"System Emergency Stopped" output
is unticked. (Installation tab > Safety >
I/O)

OSSD signals are not compatible with
the Linear Axis.

The robot was brought to a protective
stop while palletizing

A joint limit has been exceeded.

Verify that the joint speed and
position limit have been configured
correctly. Please refer to the Robot
Configurations section for more
information.

Decrease the value of the
acceleration parameter in the
Palletizer node.

Summary of Contents for PALLETIZING SOLUTION AX Series




















































































































Search results

Summary of Contents for PALLETIZING SOLUTION AX Series

Reviews:

Related manuals for PALLETIZING SOLUTION AX Series

Brands by name

Popular brands

ROBOTIQ PALLETIZING SOLUTION AX Series, Instruction Manual

Search results

Summary of Contents for PALLETIZING SOLUTION AX Series

Reviews:

Related manuals for PALLETIZING SOLUTION AX Series

Brands by name

Popular brands