ROBOTIQ PALLETIZING SOLUTION AX Series Instruction Manual Download Page 103

Page: 103 / 115

Palletizing Solution - Instruction Manual

Collisions occur with the pallet sensor
on one side, but not on the other

The column is not centered on the base.

Execute the centering procedure
found in the Installation section.

An actual collision occurred

The TCP entered is incorrect.

Confirm that the TCP has been
configured correctly

The TCP entered is incorrect since it does
not account for the bracket used.

Configure the TCP correctly.

The gripper is bigger than the box.

The size of the surface covered by the
gripper or suction device should
always be equal or smaller than the
size of the face of the box that is being
gripped. Please refer to the Other
Grippers section for more details.

The robot waits indefinitely over the
picking position

The box presence sensor is misused or
not connected.

Verify that the correct box presence
input has been selected.

Verify that the sensor used is active-
high if a sensor other than the
sensor provided is being used.

Summary of Contents for PALLETIZING SOLUTION AX Series




















































































































Search results

Summary of Contents for PALLETIZING SOLUTION AX Series

Reviews:

Related manuals for PALLETIZING SOLUTION AX Series

Brands by name

Popular brands

ROBOTIQ PALLETIZING SOLUTION AX Series, Instruction Manual

Search results

Summary of Contents for PALLETIZING SOLUTION AX Series

Reviews:

Related manuals for PALLETIZING SOLUTION AX Series

Brands by name

Popular brands