ROBOTIQ PALLETIZING SOLUTION AX Series Instruction Manual Download Page 38

Page: 38 / 115

Palletizing Solution - Instruction Manual

3. Position the robot so that the wrist is on the outside left side of the base like shown in the figure below.

4. Move the robot so the robot tool flange is parallel to the ground: change the feature reference to Base and modify the tool pos-

ition like the following: RX=0°, RY= 180°, RZ=0°.

5. Modify the Tool Position X value (base reference) to 333.35 mm (Make sure the TCP is set to 0 (the TCP menu can be found

in the Installation tab.))

Warning

Move the robot slowly and watch the movement to avoid collisions.

6. Rotate the column clockwise so that the side of the robot wrist touches the side of the base.

7. Tighten the four (4) screws to secure the column onto the base. Torque must be 50 Nm.

8. On the teach pendant, validate that the X value is still 333.35 mm.

9. Put the robot back in position of use.

Summary of Contents for PALLETIZING SOLUTION AX Series




















































































































Search results

Summary of Contents for PALLETIZING SOLUTION AX Series

Reviews:

Related manuals for PALLETIZING SOLUTION AX Series

Brands by name

Popular brands

ROBOTIQ PALLETIZING SOLUTION AX Series, Instruction Manual

Search results

Summary of Contents for PALLETIZING SOLUTION AX Series

Reviews:

Related manuals for PALLETIZING SOLUTION AX Series

Brands by name

Popular brands