ROBOTIQ PALLETIZING SOLUTION AX Series Instruction Manual Download Page 39

Page: 39 / 115

AirPick Vacuum Gripper Installation

To be able to mount the AirPick Gripper, its accessories, as well as the cable routing system, power on the robot and rotate the
joints, as described in the table below. Then, shutdown the robot

Joint

Position

Base

-180°

Shoulder

-155°

Elbow

-60°

Wrist 1

-80°

Wrist 2

270°

Wrist 3

-180°

1. If additional reach is needed, install the extra reach gripper bracket on the robot tool flange using four (4) M6 screws and tooth

lock washers and align properly with the dowel pin.

Info

Install the bracket only if necessary. Consult the

Configurator

to find out if it is needed in your case.

2. Using four (4) M6 screws and tooth lock washers, secure the coupling on the robot tool flange or on the extra reach gripper

bracket .

3. Mount the Vacuum Gripper on the gripper coupling. Align with the dowel pin.

4. Secure by inserting the M5 screws and tooth lock washers.

Summary of Contents for PALLETIZING SOLUTION AX Series




















































































































Search results

Summary of Contents for PALLETIZING SOLUTION AX Series

Reviews:

Related manuals for PALLETIZING SOLUTION AX Series

Brands by name

Popular brands

ROBOTIQ PALLETIZING SOLUTION AX Series, Instruction Manual

Search results

Summary of Contents for PALLETIZING SOLUTION AX Series

Reviews:

Related manuals for PALLETIZING SOLUTION AX Series

Brands by name

Popular brands