ROBOTIQ PALLETIZING SOLUTION AX Series Instruction Manual Download Page 107

Page: 107 / 115

Palletizing Solution - Instruction Manual

4. URCap is installed but Gripper cannot be controlled :

1. If Gripper LED is not blue, follow the steps in the first section above

2. If Gripper LED is blue, URCap is installed with the latest available version, contact

[email protected]

Driver package install:

1. Driver checkup :

a. Use the latest driver version available at support.robotiq.com

Use the installation instruction from the Installation section

b. To check your driver version :

With the Gripper unplugged

From the UR teach pendant screen, click the "Gripper" button

i. Driver version will be shown

ii. If Gripper button is not displayed, driver package is not properly installed, see instruction from the

2. Driver is installed but Gripper cannot be controlled :

a. If Gripper LED is not blue, follow the steps in the first section above

b. If Gripper LED is blue, driver is installed with the latest available version, contact [email protected]

9.2.2. Vacuum Gripper Verification

If you are not able to attain the desired vacuum level or if a diminution of the vacuum level occurs, verify:

The suction cups status

That the air path is clean and not obstructed (including the manifold)

If a filter cleaning is necessary

Summary of Contents for PALLETIZING SOLUTION AX Series




















































































































Search results

Summary of Contents for PALLETIZING SOLUTION AX Series

Reviews:

Related manuals for PALLETIZING SOLUTION AX Series

Brands by name

Popular brands

ROBOTIQ PALLETIZING SOLUTION AX Series, Instruction Manual

Search results

Summary of Contents for PALLETIZING SOLUTION AX Series

Reviews:

Related manuals for PALLETIZING SOLUTION AX Series

Brands by name

Popular brands