ROBOTIQ PALLETIZING SOLUTION AX Series Instruction Manual Download Page 64 | Manualshive

Page: 64 / 115

background image

4.2. Light States

Light States Legend

l

Blink fast: 2 Hz (0.25s ON, 0.25s OFF)

l

Blink slow: 0.5 Hz (1s ON, 1s OFF)

Color and

signal

type

Condition status

Cause or action needed (troubleshooting for e-Series)

RED

Fast blink

The linear axis controller (PLC) is unable to
communicate with the Robot controller (UR).

l

The robot has been started and needs time to boot up
(Polyscope has not loaded yet)

l

Make sure your Ethernet/USB adapter is properly connected:
the LED on the Ethernet adapter should be ON.

l

Make sure the Ethernet cable between the PLC and robot
controller is properly connected (to the USB adapter) .

l

Try pressing the Scan button in the installation tab.

l

Try powering off the system (both the robot and the linear
axis Controller). Wait 1 minute. Power up the system again.

RED

Slow blink

Communication between the robot and the
linear axis controller (PLC) is established, but
Copilot has not established the communication
yet with the linear axis controller.

l

Tap Installation → URCaps → Copilot → Linear Axis
and click on Scan button.

RED

Solid

An axis error happened.

l

Tap Installation → URCaps → Copilot → Linear Axis.
Then, check the error message and act accordingly.

RED

Solid

A Protective or Emergency stop has occurred.

l

Follow the procedures required by the system to recover
from either a Protective or Emergency stop.

YELLOW

Solid

l

When the Scan has succeeded, but the axis
brakes are not released
(Start not done yet)

l

A program is running without Palletizer node.

l

Tap Installation → URCaps → Copilot → Linear Axisand
click on Start button. You may need to press the safeguard
reset button (if you have one in your specific safety setup).

YELLOW

Slow blink

A Safeguard Stop has occured.

Press the safeguard reset button.

64

«
...
62
63
64
65
66
...
»

Summary of Contents for PALLETIZING SOLUTION AX Series




















































































































Reviews:

No comments

Related manuals for PALLETIZING SOLUTION AX Series

Brand: EAI Pages: 12

YCOO ROBO STREET KOMBAT

Brand: Silverlit Pages: 49

Brand: adept technology Pages: 52

Brand: adept technology Pages: 152

Brand: adept technology Pages: 104

Brand: adept technology Pages: 156

Brand: jbc Pages: 12

FaroArm Quantum

Brand: Faro Pages: 202

Brand: ABB Pages: 398

Brand: Miele Pages: 204

Brand: ROBOTIQ Pages: 2

CNC-RWC5-ES-UR-KIT

Brand: ROBOTIQ Pages: 2

Walking Electronic Bug WEB1

Brand: Ramsey Electronics Pages: 20

Brand: Viavito Pages: 17

Brand: Starling Technologies Pages: 29

Brand: ROEQ Pages: 31

Brand: PreCise Pages: 171

Brand: Prince Pages: 5

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands