Radyne OM20 Installation And Operation Manual Download Page 136 | Manualshive

Page: 136 / 220

background image

OM20 Universal Outdoor Modem

Web Browser/Remote Protocol

MN-OM20– Revision 5

6–62

Link Status:

The following status is available under the Monitor Menu/Link Status Sub-Menu

when the Ethernet Data Interface is selected:

Port 1 Status:

Displays the current status of LAN Port 1.

Port 2 Status:

Displays the current status of LAN Port 2.

Port 3 Status:

Displays the current status of LAN Port 3.

WAN Status:

Displays the current status of the WAN Port.

For each of the above-listed ports, the status may take on one of the following
values/meanings.

Down:

The link is down.

Unresolved:

Unable to agree on connection speed.

10 Mbps Half:

Connected at 10 Base-T Half Duplex.

10 Mbps Full:

Connected at 10 Base-T Full Duplex.

100 Mbps Half:

Connected at 100 Base-T Half Duplex.

100 Mbps Full:

Connected at 100 Base-T Full Duplex.

If all four LAN Ports are down, a Tx Data Activity Minor Alarm will be generated.
If the WAN Port is down, a Tx and Rx Ethernet WAN Major Alarm will be generated.

6.5

Terminal Mode Control

The OM20 Terminal Mode Control allows the use of an external terminal or computer to monitor
and control the modem from a full screen interactive presentation operated by the modem itself.
No external software is required other than VT-100 Terminal Emulation Software (e.g.
“Procomm” for a computer when used as a terminal. The Control Port is normally used as an
RS–232 Connection to the terminal device. The RS-232 operating parameters can be set using
the modem Front Panel and stored in EEPROM for future use (refer to Section 6.4.1 for setup and
terminal screens). Refer to Section 4 (Terminal Screen Menus) of the

“Remote Protocol For The

DMD20/DMD50/DMD2050/OM20”

Manual

(TM-117) for additional information on terminal

screen menus.

For RLLP command structure, the SNMP MIB and the Terminal Screens
reference the “Remote Protocol Manual for the (TM-117).

This specification is applicable to the DMD20, DMD20LBST, DMD50,
DMD2050, and OM20 Modems.

«
...
134
135
136
137
138
...
»

Summary of Contents for OM20





























































































































































































































Reviews:

No comments

Related manuals for OM20

Brand: Campbell Pages: 90

Brand: Ebyte Pages: 20

Brand: Ebyte Pages: 31

KeepInTouch 3766

Brand: Paradyne Pages: 108

Brand: TeleWell Pages: 131

Brand: Zoom Pages: 24

Brand: Four-Faith Pages: 33

3CP5610A - U.S. Robotics 56K V90 PCI Performance Pro Faxmodem Dos/NT/Linux

Brand: 3Com Pages: 100

Brand: 3Com Pages: 101

Cerberus P 6311-07A

Brand: Pentagram Pages: 61

Brand: Zoom Pages: 66

Brand: Vololink Pages: 50

Brand: Zte Pages: 2

MTX-3G-JAVA series

Brand: MTX Pages: 109

Brand: Bay Networks Pages: 14

Brand: Zte Pages: 17

Brand: D-Link Pages: 8

Brand: Kamstrup Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands