manualshive.com logo in svg

Radyne OM20, Installation And Operation Manual

The New Rock Technologies OM20 is a cutting-edge communication device designed to streamline your connectivity. The Quick Installation Manual provides step-by-step instructions for hassle-free setup. Download this manual for free at manualshive.com to unlock the full potential of your OM20 and enhance your communication experience.

Share
Download
background image

OM20 Universal Outdoor Modem 

Web Browser/Remote Protocol 

 

MN-OM20– Revision 5 

6–61 

When available buffer space is almost gone, the OM20 will force a collision on the input port 
when it senses an incoming packet.  This collision will cause the transmitting station to back off 
and retry the transmission. 
 
The OM20 will stop forcing collisions as soon as free buffer space becomes available. 

6.4.1.2

 

 

Full-Duplex Flow Control 

In full-duplex mode, the OM20 implements IEEE 8802.3x flow control as follows: 
 
When available buffer space is almost gone, the OM20 sends out a pause frame with the 
maximum pause time to stop the remote nodes from transmitting. 
 
The OM20 sends out another pause frame with the pause time set to zero as soon as free buffer 
space becomes available. 

6.4.2

 

Packet Statistics 

The following statistics are available under the Monitor Menu when the Ethernet Data Interface is 
selected: 
 

Total Packets:

  This Counter displays the total number of Ethernet packets received from the 

satellite. 
 

Error Packets:

  This counter displays the total number of Ethernet packets received from the 

satellite that had errors. 
 

Packet Error Rate:

  This displays the Ethernet Packet Error Rate (PER) from the satellite. 

 

Packet Statistics Reset:

  Allows the user to reset the Ethernet Total Packets and Ethernet Error 

Count by pressing <Enter>. 
 

Summary of Contents for OM20





























































































































































































































Reviews:

No comments

Related manuals for OM20

Patton electronics 1025 User Manual preview
1025
Brand: Patton electronics Pages: 9
D-Link DSL-320T User Manual preview
DSL-320T
Brand: D-Link Pages: 66
D-Link DSL-300T Install Manuals preview
DSL-300T
Brand: D-Link Pages: 26
D-Link DSL-100D Quick Install Manual preview
DSL-100D
Brand: D-Link Pages: 16
PACH & COMPANY SCWT Manual preview
SCWT
Brand: PACH & COMPANY Pages: 4
Ebyte NB144ES User Manual preview
NB144ES
Brand: Ebyte Pages: 38
Novatel Ovation MC998D Product User Manual preview
Ovation MC998D
Brand: Novatel Pages: 28
Circutor SGE-3G/GPRS Quick Start Manual preview
SGE-3G/GPRS
Brand: Circutor Pages: 2
Linksys ADSL2MUE Quick Installation Manual preview
ADSL2MUE
Brand: Linksys Pages: 110
Data-Linc Group PlantLinc PLR5000 User Manual preview
PlantLinc PLR5000
Brand: Data-Linc Group Pages: 31
MLis MLB-G1101 User Manual preview
MLB-G1101
Brand: MLis Pages: 54
Belkin F5D5730au User Manual preview
F5D5730au
Brand: Belkin Pages: 30
Belkin F1PI241EGau User Manual preview
F1PI241EGau
Brand: Belkin Pages: 52
Microflex MicroLink-HM 101-0029 Installation & Operation Manual preview
MicroLink-HM 101-0029
Brand: Microflex Pages: 17
Enfora Enabler III-G Integration Manual preview
Enabler III-G
Brand: Enfora Pages: 98
3Com 005699-00 - Manual preview
005699-00 -
Brand: 3Com Pages: 101
3Com 005605-00 Manual preview
005605-00
Brand: 3Com Pages: 115
T-Mobile W'n'W Stick IV User Manual preview
W'n'W Stick IV
Brand: T-Mobile Pages: 27

Brands by name

Popular brands

Load more brands