manualshive.com logo in svg

Radyne OM20, Installation And Operation Manual

The New Rock Technologies OM20 is a cutting-edge communication device designed to streamline your connectivity. The Quick Installation Manual provides step-by-step instructions for hassle-free setup. Download this manual for free at manualshive.com to unlock the full potential of your OM20 and enhance your communication experience.

Share
Download
background image

OM20 Universal Outdoor Modem 

Web Browser/Remote Protocol 

 

MN-OM20– Revision 5 

6–63 

6.5.1

 

Modem Terminal Mode Control 

The modem can be interactively monitored and controlled in the Terminal Mode, with a full 
screen presentation of current settings and status.  Programming is accomplished by selecting the 
item to be modified and pressing the terminal key of the option number.  For example, to change 
the transmit data rate, enter ‘33’ at the terminal.  The modem will respond by presenting the 
options available and requesting input.  Two types of input may be requested.  If the input is 
multiple choice, the desired choice is selected by pressing the ‘Space’ key.  When the desired 
option is displayed, press the ‘Enter’ key to select that option.  The other possible input type 
requires a numerical input (such as entering a frequency or data rate.  This type of input is 
followed by pressing the ‘Enter’ or carriage return key.  An input can be aborted at any time by 
pressing the ‘ESC’ key.  Invalid input keys cause an error message to be displayed on the 
terminal. 
 
The Terminal Control Mode supports serial baud rates of 150, 300, 1200, 2400, 4800, 9600, 
19200, and 38400.  The connection must be set for 8 data bits, 1 stop bit and no parity (8,N,1).  
Three terminal emulations are supported: VT-100, WYSE 50, and ADDS-VP. 
 
“$” is used for setting the screen when the terminal is used for the first time the non-volatile 
memory is reset. 

6.6

 

Modem Remote Communications 

6.6.1

 

Host Computer Remote Communications 

The Remote Port (J2) of the OM20 allows for complete control and monitoring of all OM20 
parameters and functions via an RS-232 Serial Interface, or RS-485 for RLLP Protocol.  
‘Terminal Mode’ can be entered from the GUI interface under the “System” menu by selecting 
“System” and then “Terminal” followed by “Terminal”.  The baud rate and evaluation type can 
be changed at the front panel by using the 

System>Baud Rate

 Menu. 

 
Control and status messages are conveyed between the OM20 and the subsidiary modems and the 
host computer using packetized message blocks in accordance with a proprietary communications 
specification.  This communication is handled by the Radyne Link Level Protocol (RLLP), which 
serves as a protocol ‘wrapper’ for the RM&C data.  Complete information on monitor and control 
software is contained in the following sections. 
 

 

For RLLP command structure and the SNMP MIB, reference the “Remote 
Protocol for the DMD20/DMD50/DMD2050/OM20” manual (TM-117). 

 

 

 

Notes: 

Summary of Contents for OM20





























































































































































































































Reviews:

No comments

Related manuals for OM20

FTS MICROHARD Quick Start Manual preview
MICROHARD
Brand: FTS Pages: 2
TP-Link TC-W7960 Quick Installation Manual preview
TC-W7960
Brand: TP-Link Pages: 2
TeleWell TW-VDSL2-CO Quick Installation Manual preview
TW-VDSL2-CO
Brand: TeleWell Pages: 13
THOMSON RCA DCM245 Manual preview
RCA DCM245
Brand: THOMSON Pages: 48
Motorola SURFboards SBV6220 Quick Start Manual preview
SURFboards SBV6220
Brand: Motorola Pages: 8
Motorola SURFboard SBV5322 Datasheet preview
SURFboard SBV5322
Brand: Motorola Pages: 3
Motorola SURFboard SBV6120 Quick Start Manual preview
SURFboard SBV6120
Brand: Motorola Pages: 8
Motorola SURFboard SBV5422 Installation Manual preview
SURFboard SBV5422
Brand: Motorola Pages: 33
Motorola SURFboard SBV6220 Installation Manual preview
SURFboard SBV6220
Brand: Motorola Pages: 2
Motorola SURFboard SBV6120 Installation Manual preview
SURFboard SBV6120
Brand: Motorola Pages: 27
Zte MG880 User Manual preview
MG880
Brand: Zte Pages: 43
TP-Link TD-W8960N Installation Manual preview
TD-W8960N
Brand: TP-Link Pages: 24
Four-Faith F2403 User Manual preview
F2403
Brand: Four-Faith Pages: 22
Alvarion BreezeMAX Si 4000 Installing preview
BreezeMAX Si 4000
Brand: Alvarion Pages: 8
Connected IO Verizon LT1000 2G Quick Reference Manual preview
Verizon LT1000 2G
Brand: Connected IO Pages: 6
Tahoe 681 User Manual preview
681
Brand: Tahoe Pages: 36
NETGEAR CM500 User Manual preview
CM500
Brand: NETGEAR Pages: 25
Fritz! AC430 MU-MIMO Configuration And Operation preview
AC430 MU-MIMO
Brand: Fritz! Pages: 44

Brands by name

Popular brands

Load more brands