manualshive.com logo in svg

Radyne OM20, Installation And Operation Manual

Share
Download
Radyne OM20 Installation And Operation Manual Download Page 165

MN-OM20– Revision 5 

A–1 

Appendix A.  Product Options 

A.1 

Hardware Options 

The following enhanced interface cards are available.  All options must be factory installed. 

A.1.1  G.703/IDR ESC Interface 

The OM20 can be equipped with a G.703/IDR ESC Interface.  Factory installed option 

A.1.2  Turbo Card 

The OM20 can be equipped with an optional Turbo Codec Outer Code.  This option must be 
installed at the factory and may require other options.  Factory upgrade only. 

A.1.3  Internal High Stability 

The OM20 is equipped with a 5x10

-8

 or better Stability Frequency Reference.  Standard option.  

A.1.4  DC Input Prime Power 

Allows for an optional DC Input Power Source. Factory installed option. 

A.1.5  Ethernet Data Interface 

The Ethernet interface is supported by an RJ-45, Auto-Crossover, Auto-Sensing, 10/100 Ethernet 
Data Ports.  This interface complies with IEEE 802.3 and IEEE 802.3u. Factory installed option 

A.1.6  Sequential Interface 

The OM20 can be equipped with a Sequential option.  Factory installed option 

Summary of Contents for OM20





























































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands