manualshive.com logo in svg

Radyne OM20, Installation And Operation Manual

Share
Download
Radyne OM20 Installation And Operation Manual Download Page 211

OM20 Universal Outdoor Modem 

Appendix G 

MN-OM20– Revision 5 

G–7 

Case 2:  IBS 1.544 Mbps, 3/4 Rate Viterbi 

 
Starting with the Data Rate – 512 Kbps 

 

 

Modulator: 

Method 1 - 

 

Under Interface Menu: 

Set Interface type 

 

 

 

Set Tx clock selection 

Set Framing to 1/15 
Set mode to IBS 
Under Mod Data Menu:  

Set code rate to 3/4 VIT 

 

 

 

 

 

Set data rate for 1544000  

 

 

 

 

 

Under Mod IF Menu:   Set desired Tx frequency and power level 

 

 

 

 

 

Turn IF ON 

 
Method 2 -

 

 

Under Interface Menu: 

 

 

 

 

Set Interface type 

 

 

 

 

 

Set Tx clock selection 

Set Mod strap code to: 120 

 

 

Under Mod IF Menu:   Set desired Tx frequency and power level 

Turn IF on

 

 

Demodulator:

 

Method 1 - 

 

Under Interface Menu:   

 

 

 

 

 

 

 

Set Interface type 

 

 

 

 

 

Set Buff clock selection 

 

 

 

 

 

Set Buffer Size

 

Set Framing to 1/15: 
Set mode to IBS: 
 

Under Demod IF Menu:  Set desired Rx frequency 

Under Demod Data Menu: 

Set code rate to 3/4 VIT 

 

 

 

 

 

Set data rate for 1544000  

 

 

Under Interface Menu:   

 

 

 

 

 

 

 

Set Interface type 

 

 

 

 

 

Set Buff clock selection 

 

 

 

 

 

Set Buffer Size 

Method 2 -

 

 

Under Interface Menu: 

Set Interface type 

 

 

 

 

 

Set Buff clock selection 

 

 

 

 

 

Set Buffer Size 

Set Demod strap code to: 120 

 

 

Under Demod IF Menu: Set desired Rx frequency  

Summary of Contents for OM20





























































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands