manualshive.com logo in svg

Radyne OM20, Installation And Operation Manual

Share
Download
Radyne OM20 Installation And Operation Manual Download Page 182

OM20 Universal Outdoor Modem 

Appendix D 

MN-OM20– Revision 5 

D–8 

 

D.5.1  Change Authentication Password 

The user can modify the Authorization Passwords.  The user name can have up to 14 characters 
supporting alpha and numeric characters.  Alpha characters can be entered using the up and down 
arrow keys.  Numeric characters can be selected by using the number keys on the front panel.  
The user can clear all characters from the front panel screen.   

D.5.2  Boot Mode Options (Reference only)  

Boot Modes selections are based on the networks requirements needed for setting up the Web 
browser. Refer to the manual for more specific details.  
 
Boot Mode options are:   
 

DEFAULT

 

:  

During initialization (boot up), the modem will restore the web setting to the 
standard IP Mask and addresses supplied by the modem.  The modem will be 
taken off the network and will not be accessible.  The Default settings are:  

 

 

 

IP Address Mask: 

255.000.000.000 

(FF.00.00.00 hex) 

 

 

 

Modem IP Address: 

010.000.000.001 

(C0.A8.00.EE hex) 

 

 

 

Server IP Address: 

010.001.001.001 

(0A.01.01.01 hex) 

 

 

Router IP Address: 

010.000.001.001 

(0A.00.01.01 hex) 

 

BOOTP

 

: 

  

During initialization (boot up), the modem will get the names, masks, and IP 
Addresses of the modem, router, and server.   

NON-VOL

 

:  

Stores and uses IP Mask and addresses as provided by the user. 

IP TEST

 

:  

Stores and uses IP Mask and addresses to fixed settings as listed below.

 

Bootp Server Tag: 

206 

IP Address Mask: 

255.255.255.000 

(FF.FF.FF.00 hex) 

Modem IP Address: 

192.168.0.238 

(C0.A8.00.EE) 

Server IP Address: 

192.168.000.101 

(C0.A8.00.65) 

Router IP Address: 

192.168.000.102 

(C0.A8.00.66) 

Summary of Contents for OM20





























































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands