manualshive.com logo in svg

Radyne OM20, Installation And Operation Manual

The New Rock Technologies OM20 is a cutting-edge communication device designed to streamline your connectivity. The Quick Installation Manual provides step-by-step instructions for hassle-free setup. Download this manual for free at manualshive.com to unlock the full potential of your OM20 and enhance your communication experience.

Share
Download
background image

OM20 Universal Outdoor Modem 

Web Browser/Remote Protocol 

 

MN-OM20– Revision 5 

6–52 

 

This alarm will flash on during certain modem parameter 
changes.  A solid indication points toward a problem with the 
incoming clock to the modem (SCTE). 

 
 

LB Synth PLL: 

{Pass/Fail, Unmasked/Masked} 

 

 

 

Indicates that the Rx L-Band Synthesizer is not locked.  This 
alarm will flash on during certain modem parameter changes.  A 
solid indication points toward a configuration problem within the 
modem. 

 
 

LNB Current:

 

{Pass/Fail, Unmasked/Masked} 

 

 

 

Indicates that current is either below or above the threshold 
limits of the LNB, as specified by the OM20.  Only active when 
LNB Voltage is enabled. 

 

 

LNB Voltage:

 

{Pass/Fail, Unmasked/Masked} 

 

 

 

Indicates that voltage is not functioning correctly when voltage 
is enabled. 

 
 

Ethernet WAN: 

{Pass/Fail, Unmasked/Masked} 

 

 

 

Indicates that the interface card is faulted and will not pass data 

(displays only when the Ethernet Card is installed and the 
Ethernet Interface is selected). 

 

 

MINOR ALARMS 

 
 

Buffer Underflow: 

{Pass/Fail, Unmasked/Masked} 

 

Indicates that a Doppler Buffer underflow has occurred. 

 
 

Buff Near Empty: 

{Pass/Fail, Unmasked/Masked} 

 

 

 

 

Indicates that the Doppler Buffer is about to underflow. 

 
 

Buff Near Full: 

{Pass/Fail, Unmasked/Masked} 

 

 

 

 

Indicates that the Doppler Buffer is about to overflow. 

 
 

Buffer Overflow: 

{Pass/Fail, Unmasked/Masked} 

 

 

 

 

Indicates that a Doppler Buffer overflow has occurred. 

 

 

 

Rx Data Activity: 

{Pass/Fail, Unmasked/Masked} 

 

Indicates that there is no Rx Data activity. 

 
 

Satellite AIS: 

{Pass/Fail, Unmasked/Masked} 

 

 

 

 

Indicates that AIS has been detected in the receive satellite data 
stream. 

 
 

DnI Frame Lock: 

{Pass/Fail, Unmasked/Masked} 

 

 

 

 

Indicates if drop/insert data is frame locked. 

 
 

DnI MFrame Lock: 

{Pass/Fail, Unmasked/Masked} 

 

Indicates if drop/insert data has multiframe lock. 

 
 

Insert CRC: 

{Pass/Fail, Unmasked/Masked} 

Summary of Contents for OM20





























































































































































































































Reviews:

No comments

Related manuals for OM20

M/A-Com P5100 Series Installation And Operator'S Manual preview
P5100 Series
Brand: M/A-Com Pages: 22
Toshiba PCX1000 Owner'S Manual preview
PCX1000
Brand: Toshiba Pages: 18
Toshiba PCX1100 - DOCSIS Cable Modem Owner'S Manual preview
PCX1100 - DOCSIS Cable Modem
Brand: Toshiba Pages: 21
Toshiba PCX2500 Owner'S Manual preview
PCX2500
Brand: Toshiba Pages: 22
Toshiba DAZ8823A Owner'S Manual preview
DAZ8823A
Brand: Toshiba Pages: 22
Toshiba DAZ8817F Owner'S Manual preview
DAZ8817F
Brand: Toshiba Pages: 22
Toshiba DOCSIS DAZ8820F Owner'S Manual preview
DOCSIS DAZ8820F
Brand: Toshiba Pages: 22
Toshiba P000233790 Owner'S Manual preview
P000233790
Brand: Toshiba Pages: 53
Scientific Atlanta WebSTAR DPX110 User Manual preview
WebSTAR DPX110
Brand: Scientific Atlanta Pages: 92
Zoom 5697 Quick Start Manual preview
5697
Brand: Zoom Pages: 36
Ebyte 433D20 User Manual preview
433D20
Brand: Ebyte Pages: 17
M2M Sixnet Series Hardware Manual preview
Sixnet Series
Brand: M2M Pages: 32
DPL Hercules Quick Install Manual preview
Hercules
Brand: DPL Pages: 13
PairGain CRA-C User Manual preview
CRA-C
Brand: PairGain Pages: 86
UIS WFM-220 User Manual preview
WFM-220
Brand: UIS Pages: 4
Rae RAELink3 User Manual preview
RAELink3
Brand: Rae Pages: 42
Navini Networks Ripwave Surfer 1239 User Manual preview
Ripwave Surfer 1239
Brand: Navini Networks Pages: 32
Wavenet Technology DWM0001 User Manual preview
DWM0001
Brand: Wavenet Technology Pages: 35

Brands by name

Popular brands

Load more brands