manualshive.com logo in svg

Radyne OM20, Installation And Operation Manual

Share
Download
Radyne OM20 Installation And Operation Manual Download Page 116

OM20 Universal Outdoor Modem 

Web Browser/Remote Protocol 

 

MN-OM20– Revision 5 

6–42 

 

 

ES to ES Enhanced:  Allows user to select the Interface Baud 
Rate.  This selection will allow the user to set rate as listed in 
Table 3-3. 

 
 

 

SCC:  Allows user to select the interface Baud rate.  Interface 
Rate must be equal to or greater than the In-Band Rate.   

 
 

ES Bits/Char: 

{7,8}

 

 

 

Allows the user to choose between 7 or 8 bit data.

 

 
 
INSERT MAP

  

The Insert Map displays the current programmed Rx Insert map 
for the modem.  (Refer to Section 3.13, “Drop and Insert 
Mapping” in this manual). 

 

 

 

 

Insert Mode: 

{NONE, T1-D4, T1-ESF, PCM-30, PCM-30C, PCM-31,       
PCM-31C, T1-D4-S, T1-ESF-S.} 

 

 

 

Insert mode may only be changed from none when the drop and 
insert specified is in use. 

 
 

 

Submit Map: 

Allows the user to Submit the Rx D&I Map Time Slots. 

 
 

 

 

Reset Map: 

Allows the user to reset the Rx D&I Map Time Slots. 

 
 

 

 

T1/E1 Frame Src: 

T1/E1 FRAME SRC  {INTERNAL, EXTERNAL} 

 

 

Selects the frame source for T1 or E1 framing. 

 
 

Terrestrial Time Slot: 

{1-31} 

 

 

 

Allows the user to edit the Rx Edit map to specify the terrestrial 
slots that will be inserted into the assigned satellite channels.  
The satellite channels are fixed and the number of channels are 
determined by the data rate.  The terrestrial time slots available 
are determined by the drop mode.   

Summary of Contents for OM20





























































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands